Consider a metal single crystal oriented such that the normal to the slip plane and the slip direction are at angles of 43.1° and 47.9°, respectively, with the tensile axis. If the critical resolved shear stress is 20.7 MPa (3000 psi), will an applied stress of 45 MPa (6500 psi) cause the single crystal to yield? If not, what stress will be necessary?

Q: Some aircraft component is fabricated from an aluminium alloy that has a plane strain fracture…

A: Case 1) Stress=300MPa Internal crack length =4mm Case 2) Stress=260MPa Internal crack length =6mm

Q: In an engineering application, the material is a strip of iron with a fixed crystallographic…

A: Given: The yield strength of material for grain size of 30 microns, σ₁ = 110 MPa The yield strength…

Q: Determine the critical resolved shear stress on a BCC single crystal if a normal stress of 10 MPa…

A: Given data: Normal stress σ=10 MPa acts along l=[100] direction. Applied stress causes slip in the…

Q: You have been asked to draw up a specification for a ceramic cladding tile that is likely to…

A: Critical stress formula in terms of Youngs Modulus, surface energy and crack length is used.

Q: A steel plate, which has a fracture toughness in a plane strain state of 83 MPavm, is alternately…

A: Given Data: KIC=83 MPamσmax=750 MPaσmin=20 MPaf=1n=2.8ai=0.0015 mm   To Find: Determine the value of…

Q: t as a separate question that has no relationship to previous parts of the question. 1 and 2 are…

A:

Q: A component made of 7075-T6 aluminum alloy has an edge crack of 1.4 mm in length. Plane strain…

A: Given: The edge crack of aluminum alloy is 1.4 mm. The plane strain fracture toughness is 27 Mpam.…

Q: Some aircraft component is fabricated from an aluminium alloy that has a plane strain fracture…

A:

Q: What is the magnitude of the maximum stress that exists at the tip of an internal crack having a…

A: Given data:We need to find the The magnitude of the maximum stress that exists at the tip.

Q: A single crystal metal test sample oriented such that a tensile stress is applied in the [012]…

A:

Q: Consider a metal single crystal oriented such that the normal to the slip plane and the slip…

A: Given data ϕ=35.5°λ=25.4°τ=25 MPaσ=30 MPa

Q: The compressive strength of alumina quartz (Al2O3) is 2.1 GPa. A quartz tube is being used for a…

A:

Q: A solid has a Young's modulus of 100 GPa and Poisson's ratio of 0.30. Consider a mode I crack in…

A: Given: The elastic modulus, E = 100 GPa The poisson ratio, ν = 0.3 The stress intensity factor, K =…

Q: A gear pair is designed to provide a 3:1 reduction in speed. The design uses 12 DP gears, driving a…

A:

Q: When λ=1.5Å and θ=30°, how much strain (Δd/d) is needed to cause a peak broadening same as that of…

A: This problem is related to Braggs law.  if λ is the wavelength of X-ray,d is the distance between…

Q: The yield stress for a metal changes from 410 Nmm^-2 to 670 Nmm^-2 when the average grain diameter…

A: Given:σy1=410 N/mm2    σy2=670 N/mm2d1=0.053 mmd2=0.037 mmdavg=0.045 mmσy=560 N/mm2

Q: An airplane part is to be designed from view point of Fracture Toughness for which two materials are…

A: Write the expression for the surface crack length. Here, K represents the fracture toughness, Y…

Q: What is the Distortion energy failure theory? Under what loading types and materials would you use…

A: The Distortion energy failure theory states that a material yields or fails when the total…

Q: What minimum specimen diameter is required to ensure

A: Given datathe three-point transverse bending test,the square section of side a= 18.5 mm= 0.0185mThe…

Q: There are three slip systems on a FCC octahedral plane, i.e. one of the {111} planes. Assume a 2 MPa…

A: "Since you have asked multiple questions, we will answer the first question for you. If you want any…

Q: An 820 MPa (145,000 psi) stress is applied to a specimen of 4341 steel alloy, which has a plane…

A: Given Data

Q: A sample is made of a făce-centered cubic (fcc) single crystal. The sample starts to have plastic…

A: Given: The stress along {012} direction = 100 MPa

Q: A monocrystal of a CCC metal is oriented so that the direction [001] is parallel to an applied…

A: Given data A mono crystal of a bcc metal is oriented so that  the direction is parallel to the…

Q: 1.) Assume that a wing component on an airplane is made of an aluminum alloy with a plane strain…

A: Disclaimer: Since you have asked multiple question, we will solve the first question for you. If you…

Q: An aircraft skin panel that is part of a commercial airline is to be made from aluminium alloy…

A:

Q: From the work of D. C. Jillson, Trans. AIME 188, 1129 (1950), the following data were taken relating…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: f 800 MPa, and a tensile this specimen experienc long? Why or why no

A:

Q: You are given 1) the normal to the slip plane and the normal to the slip direction angle with the…

A:

Q: Determine the critical resolved shear stress on a BCC single crystal if a normal stress of 10 MPa…

A: Write the formula for the angle between two planes with Miller indices [u1 v1 w1 ] and [u2 v2 w2].…

Q: How can the strain-energy density be determined?

A: Strain energy is defined as the energy absorbed by any member when work done by any load deforms…

Q: 7.12 Consider a metal single crystal oriented such O that the normal to the slip plane and the slip…

A: As per given question Consider a metal single crystal oriented such that the normal to the slip…

Q: Some aircraft component is fabricated from an aluminium alloy that has a plane strain fracture…

A:

Q: The part of the vehicle is production from an magnesium alloy ,if KIC 40 MPa√m. The fracture…

A: Fracture toughness of a material is defined as the measure of ability of the material to withstand…

Q: Q2:- The part of the vehicle is production from an magnesium alloy .if KIC 40 MPavm. The fracture…

A: In general, the fracture toughness of a material is defined as the ability of the material with…

Q: A brass specimen of the circular cross-section is fractured at 147 kN force and the final length of…

A: Result : 1)  The diameter of the specimen is 1.539 mm 2) The initial length of the specimen is…

Q: 7.12 Consider a metal single crystal oriented such + that the normal to the slip plane and the slip…

A: .

Q: Which one of the following materials would plastic deformation through twinning be the most likely…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Define the term“volumetric strain?

A: When the body is subjected to stress, it deforms in all three directions. That will lead to a…

Q: iv) Young's Modulus if the elongation is 2.4 mm at 17 kN and (v) Final diameter if the percentage of…

A: