7.12 Consider a metal single crystal oriented such O that the normal to the slip plane and the slip di- rection are at angles of 60° and 35°, respectively, with the tensile axis. If the critical resolved shear stress is 6.2 MPa (900 psi), will an applied stress of 12 MPa (1750 psi) cause the single crystal to yield? If not, what stress will be necessary?

7.12 Consider a metal single crystal oriented such O that the normal to the slip plane and the slip di- rection are at angles of 60° and 35°, respectively, with the tensile axis. If the critical resolved shear stress is 6.2 MPa (900 psi), will an applied stress of 12 MPa (1750 psi) cause the single crystal to yield? If not, what stress will be necessary?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the Free-body diagram in the image below of the BLOCK, and accurately label everything. Including the angles, force /spring force and weight etc draw it accurate No solving required just the fully labeled Free body diagram
13-9. The gas steorage tank is fabricuted by bolting togeth- er two half cylindrical thin shells and two hemispherical shells as shown. If the tank is designed ta withstand a pres- sure of 3 MPa, determine the required minimum thickness of the cylindrical and hemispherical shells and the minimum required number of bolts for each hemispherical cap. The tank and the 25 mm diameter bolts are made from material having an allowable narmal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m.
*6-12. Locate the centroid I of the area.
Two uniform spheres are positioned as shown. Determine the gravitational force F which the titanium sphere exerts on the copper sphere. The value of R is 55 mm. Copper y T 2.1 R j) (10-8) N R 4.6 R Titanium Answer: F = (i 26° - X i + i
HW3-11
Two uniform spheres are positioned as shown. Determine the gravitational force F which the titanium sphere exerts on the copper sphere. The value of R is 30 mm. y Copper T 2.5 R x i + i j) (10-8) N R 4.9 R Titanium Answer: F = (i 27°
Determine the reactions at the supports. Assume A and B are pins. EI is constant.
*9-72. The cylinder CD af the assembly is heated from T, = 30 °C to T, = 180 °C using electrical resistance. At the lower temperature T, the gap between C and the rigid bar is 0.7 mm. Determine the force in rods AB and EF caused by the increase in temperature. Rods AB and EF are made of steel, and cach has a cross-sectional area of 125 mm. CD is made of aluminum and has a cross-sectional area of 375 mm. E = 200 GPa, Ea = 70 GPa, and au = 23(10)/C a7 mm ல் mm 300் m
Determine the vertical displacement of joint C. Assume the supports at A and E are pins and joint C is pin connected. EI is constant. Use the method of virtual work.
7-18. The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. Determine the resultant internal loadings acting on the cross section at point C. The 400-N forces act in the -z direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and z components of force on the shaft. X A 200 mm 300 mm 200 mm 400 N 150 mm 150 mm 400 N D 400 mm 200 N Prob. 7-18 B 200 N Z 80 N 80 N y
Each cord can sustain a maximum tension of 700 N . Determine the largest mass of pipe that can be supported.
1-18. Determine the specific weight of hydrogen when the temperature is 85°C and the absolute pressure is 4 MPa.