Calculate (a) the wire diameter; (b) the mean coil diameter; and (c) the number of coils (G = 40 GPa)

Q: 2- the rubber blocks shown in Figure 2 are used in a double U shear mount component. The dimensions…

A:

Q: If the radius of wire stretched by a lo= doubled then its Young's modulus (a) will be doubled (b)…

A: we know that Young modulus is equal to the ratio of stress and  the strainY=σεY=FA∆ll

Q: A structure consists of three copper rods with circular cross-sections fixed to the ground that are…

A:

Q: The truss in the figure below is under the effect of one load, this truss consists of three parts,…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: You are holding a thin and weightless bar on your head (see figure 2.1). On the extremity A, the bar…

A: Given:k=50 N/mAE=1.58496 m

Q: Question 4: A riveted joint is shown in the figure which is used in the bridge to lock the wire, By…

A: Given

Q: Truck suspensions often have "helper springs" that engage at high loads. One such arrangement is a…

A:

Q: then rounding-off to 5 decimal places yields 1.23457 and that is the value which you need to type in…

A: Given: Horizontal force→P=2600 lb Cross sectional area of the truss→A=2 in2=0.013 ft2 Youngs…

Q: The pulleys in the system are under the influence of the forces shown in the figure. The yield…

A:

Q: A rigid rod ABCD is supported by wires BE, CG and pretension cord that wraps over a frictionless…

A: Step 1: Step 2:Step 3: Step 4:

Q: You are holding a thin and weightless bar on your head (see figure 2.1). On the extremity A, the bar…

A: Given:k=50 N/m

Q: Ask Copilot + เท (b) of 7 A Question 5 A steel bar AD shown in Figure Q5 has a cross-sectional area,…

A: The change in length of the bar can be calculated using the formula:ΔL = PL/EAwhere ΔL is the change…

Q: For the spring assemblages shown in Figure, determine the nodal displacements, the forces in each…

A:

Q: Q2) A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft providing 4…

A: The number of plates on the driving shaft is n1=3. The number of plates on the driven shaft is n2=2.…

Q: What is the minimum required diameter of the rod if the factor of safety for tension failure is F.S.…

A: Given,load, P = 11 kN = 11,000 NFailure stress, σ= 60 Mpa = 60 N/mm2Factor of safety, FS =…

Q: A copper bar with rectangular cross-section is hung from a rigid pin that is supported by two steel…

A:

Q: In the arrangement shown in the figure, a cable is attached to the end of a cantilever beam. We will…

A:

Q: The rod length in the figure is L = 28 cm and the profile section is 6x6 cm. Rod pull with a…

A:

Q: Q-11 The rigid plate in Figure Q-11 is supported by bar (1) and by a double-shear pin connection at…

A: Write the given information.

Q: Solve the problem

A: Step 1: Step 2:

Q: Figure Q4(a) shows the stress-strain curves of material A and material B. A circular rod of material…

A:

Q: Mechanical Engineering There is a spring with a repeated compressive load between 50N and 100N.…

A: according to the details provided

Q: A plat spiral spring is made of 6 mm wide.and 2.5 mm thick wire andis 250 cm long. Assuming the…

A: Given data: width of spring = 6 mm Thickness of wire = 2.5 mm length = 250 cm Maximum stress = 840…

Q: Abar having a length of 5 in and cross-sectional area of 0 7 in² is subjected to an axial force of…

A: Given data:- Length of the Bar =5 in cross-sectional area =0 7 in2 axial force= 8000 lb Deformation…

Q: A circular bar of magnesium alloy is (700+Reg/10) mm long. The stress-strain diagram for the…

A: Given data: Length of magnesium alloy, L = (700+Reg/10) mm. The value for Reg, Reg = 66.…

Q: A spring (squared and ground) having a pitch 0.75 inch has a mean diameter of 1.5in and a wire…

A:

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

A: The bar 1 is bronze The area of bar 1 is The bar 2 is aluminum The area of bar 2 is The clearance at…

Q: A rod of 15mm diameter is held without being stressed between rigid walls as shown. The coefficient…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: Two springs are arranged in parallel with spring constants 21 N/mm and 34 N/mm. A force of 224 N is…

A:

Q: The metallic hollow pipe shown in Figure Q1 is fixed at both its ends, and is under axial…

A:

Q: A 3-meter long pin-ended aluminium rod is loaded along its longitudinal axis with a 50 kN…

A: length L = 3m = 3000 mmload P = 50 kN = 50 x 103 NExternal dia D = 65 mmyield strength = 100 MPa =…

Q: a helical compression spring with squared and ground ends is made of shot-peened astm a232 spring…

A:

Q: Part (a) of the figure below shows a knuckle joint with a pin inside it. This joint is subject to a…

A: Given-Fluctuating load F-on and 600NAISI Hot- rolled stealFatigue stress concentraion factor-

Q: A coil spring with 5 cm outside diameter is required to work under the load of 190 N. The wire…

A: Outside Diameter (D) = 5 cm = 50 mmWire Diameter (d) = 5 mm Active Coils = 6

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G=11,500 ksi] shaft is not to…

A:

Q: 4-8. For a close-coiled helical spring subjected to an axial load of 300 N having 12 coils of wire…

A: Given, The mean coil diameter, D=250 mm The wire diameter, d=16 mm Number of coils, n=12 Axial load,…

Q: 4. The section of peripheral nerve in neck is under tension of force F=0.18N due to sudden movement…

A:

Q: 1.37 Link BC is 6 mm thick, has a width w = 480- MPa ultimate strength in tension What was the…

A:

Q: A stepped bar is fixed at end C. The bar has a cross sectional area of 1000 mm² in AB, and a 2000…

A:

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.