Mechanical Engineering There is a spring with a repeated compressive load between 50N and 100N. Calculate the fatigue life and natural frequency of the following springs. (D = 50mm, d = 5mm, N = 10, r = 7800kg/m3, G = 75GPA, nsafe = 1.25) Shear Strength Unit Static intensity 140 MPa 2.15 Fatigue strength (S = 10°N Mpa) -0.05

Mechanical Engineering There is a spring with a repeated compressive load between 50N and 100N. Calculate the fatigue life and natural frequency of the following springs. (D = 50mm, d = 5mm, N = 10, r = 7800kg/m3, G = 75GPA, nsafe = 1.25) Shear Strength Unit Static intensity 140 MPa 2.15 Fatigue strength (S = 10°N Mpa) -0.05

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Values are m= 360mm n= 375mm q= 24mm r= 18mm P= 0.6kN
Two forces are applied to a flywheel 50 cm in diameter. Each force is 500 N. The shaft is fixed to the wall using three grade 5 steel bolts. The distance between the bolts and the axis of rotation is 10 cm. (a) What moment of resistance must develop the three bolts together Answer: 250 Nm (b) What is the resistance force F of each bolt? Answer: 833.3 N (c) What is the diameter of the bolts if their factor of safety is 10? Answer: 4.14mm
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Сopper Area, A 900 mm2 1200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 МPа 70 MPa Which of the following most nearly gives the load, in percent, carried by the copper? Select the correct response 44. 44% 55.56% 66.67% 33.33%
Q2/ A force P = 1 KN applied to a right bar suspended by three wires, as shown below. all wires are of equal size and the same material. for each wire, A = 80 mm , E =200 GPa , and L =4 m. If initially, there were no slack in the wires, how will the applied load distribute between the wires? 200 100 100 4000 mm mm mm mm
FN = 50
Compute the minimum vine diameter to provide a desired factor of safety of 1.7 against yield-type failure. Assume a yield stress of 300 MPa, and that the mass of the monkey is 65 kg. Hint Weight (N) = Mass (Kg) X g (9.81 m/s2)
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
In mechanical resistance
Need Help With This Question
A hard-drawn steel wire extension spring has a spring index Of 7.5, hook radii of r = 0.106 in and r2 0.089 in, and an initial tension of 1.5 lbf. The number of body turns is 13.5 and the uncorrected initial stress is 16.5 kpsi. From the given information: (a) Determine the physical parameters of the spring. (b) Find all stresses at ends A and B and the body torsion under the static load of 6 Ibf.
Material property of the given system: Tensile strengthσt=11000 daN / cm^2 and Torsional strengthSince τ=5000 daN /cm^2, find the System's Coefficient of Safety (EMF cis) for only point A using the MOH'R circle method?(Dimensions are given on the system) Rod diameter D=4 cm, Rod length L=100 cm, Vertical applied to the rodforce F=500 daN and Torque T=1000 daN cm
7:Y. O %Y. O 36 ll ll くロ quiz 2 elearning.uowa.edu.iq Marked out of 1.00 P Flag question quiz 2: flexural stress which fluctuates between + 250 MN/m2 and - 115 MN/m² applied on a machine component. Calculate the ultimate strength value according to Goodman's relation. Take yield strength = 0.55 Ultimate %3D strength; Endurance strength = 0.5 Ultimate strength; and factor of safety = 1.5. A- В I D II