A structure consists of three copper rods with circular cross-sections fixed to the ground that are connected to a rigid bar. A stainless steel rod, also with a circular cross-section, is fixed to the rigid bar as shown, and a force of 25 kN is applied to the end of the stainless steel rod. The elastic modulus of copper is 101 GPa, and the elastic modulus of stainless steel is 193 GPa. The diameters are as follows: dsteel= 45 mm and dcopper 20 mm. Find the total upward displacement of point G

A structure consists of three copper rods with circular cross-sections fixed to the ground that are connected to a rigid bar. A stainless steel rod, also with a circular cross-section, is fixed to the rigid bar as shown, and a force of 25 kN is applied to the end of the stainless steel rod. The elastic modulus of copper is 101 GPa, and the elastic modulus of stainless steel is 193 GPa. The diameters are as follows: dsteel= 45 mm and dcopper 20 mm. Find the total upward displacement of point G

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: The aluminum bar with cross-sectional area of 160 mm2 carries the axial loads at the position shown…

A: Cross sectional area A = 160 mm2 E = 70 GPA

Q: . A thin plate is composed of four CST elements, as shown inthe figure below. The plate is subjected…

A: I have attached the image below Explanation:

Q: Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. Aluminum…

Q: Three solid cylindrical rods are welded together to form the compound axial member shown in the…

A: This question is related to solid mechanics. deformation is defined as the extension or compression…

Q: investigate whether the safety requirement

Q: A vertical bar consists of three prismatic segments AB, BC, CD with cross sectional areas 6000 mm²,…

Q: Rigid bar ABC is supported with a pin at A and an elastic steel rod at C. The elastic rod has a…

A: Consider below FBD for the given question: Here, A-C-B = Original bar AB A-C'-B' = Deformed bar AB…

Q: Problem # 5 The 1.75 in thick rubber pads are bonded to three plates to form the shear mount shown…

A: F=1200 lbE=480 psiv=0.52t=1.75 in

Q: A stepped bar is fixed at end C. The bar has a cross sectional area of 1000 mm² in AB, and a 2000…

Q: A bar ABC length L consists of two parts of equal lengths but different diameters.Segment AB has…

A: Given: P=110 kN shortening of the bar = 0.8 mm (a)Maximum allowable diameter (b) distance b from…

Q: Consider a structure including the horizontal beam AB hinged to the wall at point A and supported by…

Q: A rectangular bar of length L has a slot in the central half of its length. The bar has width b,…

A: Write the given data. L=520 mmE=74 GPaσavg=190 MPa

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Stainless Steel
Copper
P = 25 KN
D
G
E
F
7m
4.5 m
A structure consists of three copper
rods with circular cross-sections fixed to
the ground that are connected to a rigid
bar. A stainless steel rod, also with a
circular cross-section, is fixed to the
rigid bar as shown, and a force of 25 kN
is applied to the end of the stainless
steel rod. The elastic modulus of copper
is 101 GPa, and the elastic modulus of
stainless steel is 193 GPa. The
diameters are as follows: dsteel= 45 mm
and dcopper 20 mm. Find the total
upward displacement of point G
from its original position.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data.

VIEW

Step 2: Calculations for displacement of point G.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. A compressed bar having a square cross of width b must support a load P = 37kN. The two parts of the bar are connected by a glued joint along plane p-q, which is at an angle a = 40° to the vertical. The bar is constructed of a structural plastic for which the allowable stresses in compression and shear are 7.6 MPa and 4.1 MPa, respectively. In addition, the allowable stresses in the glued joint are 5.2 MPa in compression and 3.4 MPa in shear. 9 b Determine: a) compressive stress (MPa) in the glued joint b) shear stress (MPa) in the glued joint c) compressive stress (MPa) in the plastic bar d) max. shear stress (MPa) in the plastic bar e) the minimum width b (cm) of the bar based on shear in the glued joint as the failure mode ~2~
An idealized model of a thin-walled convertible car body cross-section is shown in figure Q16. The effect of doors and windows has been ignored. The car has vertical side walls of thickness t1 and length 1 m and a horizontal base of thickness t2 and length 1.9 m. It is constructed from aluminium with a shear modulus of 24 GPa. t₁ = 15 mm t2 = 15 mm a. For this open section determine the torsional stiffness? Give your answer to 3 significant figures in Pa m4 and non-scientific notation e.g. 10000 rather than 10e05. Do not include units in your answer Note that for an open section, the total area moment JT is the sum over all plates i as given by equation (1) below. Ir = = = Ei bit? Torsional stiffness = GJT t₂ 1.9 m 1m Figure Q16 - idealised model of a thin-walled convertible car body
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.
The figure shown below
Question 1 A steel bar with length of 4.5 m is subjected to forces as shown in the figure: 1. Determine the stress in the square section 2. Determine the elongation of each sections Take the modules of elasticity for the bar is 200 GPa Circular section Square section Circular section Diameter =15 mm Area =20 mm*20mm Diameter =10 mm 50 kN 35 kN 30 kN 45 kN 1 m 2 m 1.5 m
3. The bar shown below is composed of two pieces, AC and CD. The bar is attached to the wall at point A. The length L = 10 in. The cross sectional areas are: AAC = 4 in? and AcD = 2 in?. The Young's Moduli are: EAC =20 Msi and Ecd= 15 Msi Two forces are applied at points B and D: PB = 50 kips and PD = 20 kips. Determine: (a) the reaction force at A (specify –→ or +) and (b) the deflection of point D (specify → or +). (Hint for (b): Think about how many pieces you must subdivide the rod into.) Ans: RA = 30 kips (+), dp = 7.9167×10-3 in (E) A В C D Pp L 2L L
Please show the formula used and free body diagram A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 × 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
Consider the two bars of identical material with their elastic modulus E as shown in Figure below. Both bars have the same circular cross-section with diameter of d. The length of the longer bar is 2L and the length of the shorter bar is L. The angle between the bars is B. The system is subjected to a vertical force acting at point Pas shown in the figure with a magnitude of F. Calculate horizontal and vertical components of the displacement of point P. Use engineering notation (ENG display mode on scientific calculators) with 3 significant figures after the decimal point. E (psi) 1.50E+06 d (in) 1.25 L (in) 12 Beta (degrees) 30 F (Ibf) 110 F P L 2L
A steel pipe (1) is attached to an aluminum pipe (2) at flange B. Both steel pipe (1) and aluminum pipe (2) are attached to rigid supports at A and C, respectively as shown in figure2. Member (1) has a cross-sectional area of A1 = 3600 mm, an elastic modulus of E = 200 G Pa and an allowable normal stress of 160 M Pa. Member (2) has a cross-sectional area of A2 = 2000 mm2 , an elastic modulus E = 70 M Pa and an allowable normal stress of 120 MPa. Determine the maximum load P that can be applied to flange B without exceeding either allowable stress.
L1 PB 2 E2 L2 D2 Dimensions: L2 L1 D2 D1 17 mm 18 cm 23 cm 15 mm Problem Statement: The rod shown is subjected to loads of PR = 112 kN and Pe = 18 kN. Segments AB and BC have elastic moduli of E, = 206 GPa and E = 73 GPa. The rod has circular cross-sections, and the dimensions of the rod are given above. Find the overall change in length of the rod under this load. Assume: • The collar at B is rigid • Stress concentration effects may be neglected 2014 Michael Swanbom
4. A ball in a cylindrical inner race has a radius of 5mm. The radius from the center of the race to the bottom of the groove is 20mm. If a load of 1,500N is applied: A. Find the dimensions of the contact ellipse B. Find the maximum deformation *Esteel = 207MPA, Vsteel = 0.3
I am struggling with this question