A rigid rod ABCD is supported by wires BE, CG and pretension cord that wraps over africtionless pulley as shown in Figure Q3. Wire BE is made from steel (Est = 210 GPa) andwire CG is made from aluminium (Eat = 70 GPa). The diameter of wires BE and CG are 30mm, respectively. If the tension of the cord connected to the rigid rod at point D is 50kN,determine,a) Internal force in each wire, BE and CG.b) Average normal strain in each wire, BE and CGc) Displacement of point D.300 mm250 mm420 mm350 mm350 mmfirinP=50kN130°

Answered: A rigid rod ABCD is supported by wires…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3,700 N/m, that are attached to a threaded rod. The pitch of the threads is p = 1.5 mm. b В A -Hanger Frame Parallel Knurled nut - springs Threaded rod D Threaded, rod Knurled nut Parallel springs Top view of the springs If the weight is 63 N, how many revolutions of the nut are required to bring the pointer back to the mark? revolutions
A bridge truss extends x = 206 m across a river (shown in the figure below) where 8 = 39º. The structure is free to slide horizontally to permit thermal expansion. The structural components are connected by pin joints, and the masses of the bars are small compared with the mass of a 1340 kg car at the center. Calculate the force of tension or compression in each structural component (in N). B TAB = TAC = TBC = TBD TDE TDC= TEC = 11 N ---Select--- N ---Select--- N ---Select--- N ---Select--- N ---Select--- N ---Select--- N ---Select--- C X D E
A sign for a pizza restaurant hangs from a 2.60-m long rod extended out from a building. A cable, attached to the building, is attached to the rod at a point that is 2.10 m from the hidge. (See the figure.)The mass of the rod is 5.90 kg. The mass of the sign is 9.40 kg. The angle between the building and the rod is 74.0 degrees. The angle between the cable and the horizontal is 31.0 degrees.What is the torque on the rod due to the weight of the rod alone? [Take the axis to be at the hinge.]
3 Q2 A beam, AB, of weight W= 50 N and length L = 0.8 m is supported by two springs, as shown in figure 2.1. The two springs have identical unstressed length; the spring on the left has a spring constant, k, = 200 N/m, while the one on the right has a spring constant, k₂= 100 N/m. A vertical and downward load, P = 40 N, is applied at a distance x from A. (i) Derive the value of x for which the beam will have a horizontal orientation at equilibrium. State and justify your assumptions and comment on your working. bewalls (ii) Assume the two springs have different unstressed lengths. In your own (exham Or words, show whether it is possible for the beam to have a horizontal orientation at equilibrium when one spring is stretched while the other spring is compressed. State and justify your assumptions and comment on your working. kı k₂ (oisse of ton) 1. etgR B 10964 mtsnimsx3 to bn3 P Figure 2.1 (not to scale) A inction, and
Problem 2 In the system below, two rigid bodies (Nodes 1 and 3) are connected by four springs to walls on either side, as shown in the figure. Nodes 2 and 4 are fixed (wall). An external force of 10 N is applied to body 1 (Node 1). The spring constants are given as kı=10 N/m, k2=20 N/m, k3=30 N/m, and k4=40 N/m. Assume that the bodies can only undergo translation in x-direction (1 DOF). Using the direct method: a) Find the displacements of the two rigid bodies (Nodes 1 and 3). Hint: units! b) Find the reaction force at the left wall (Node 4). Hint: units! E1 E2 3) F1 www 4 Е4 X
The beam shown in Figure Q.2 consists of a W610 x 140 structural steel wide-flange shape [E= 200 GPa; /= 1120 x 106 mm²]. If w= 65 kN/m and P= 124 kN, determine: AY, V 1.5 m B W 3.5 m P C 2.5 m D Figure Q.2 Part A: The reactions at A, B, and D. Choose the reaction force at B as the redundant; therefore, the released beam is simply supported between A and D. Part B. The magnitude of the maximum bending stress in the beam. f) Find the maximum bending moment in the beam. Enter your answer in kNm to two decimal places. g) Calculate the magnitude of the maximum bending stress in the beam. Enter your answer in MPa to two decimal places
QUESTION 2 A two-bar planar truss structure has the geometry as shown in Figure Q2. A concentrated force P = 200 kN is applied to the truss at joint C, in the direction shown. Member AC is made of steel (E200 GPa) and has cross-sectional area of 1200 mm² while member BC is made of aluminum (E = 70 GPa) with cross-sectional area of 1500 mm². By using point A, B, and C as node 1, 2, and 3, respectively, the nodal coordinates and the elements connectivity are chosen as shown in the following tables: NODAL COORDINATES NODE x (m) 1 2 3 0 6 3 y (m) 0 -2 2 ELEMENT CONNECTIVITY ELEMENT 1st NODE 2nd NODE 1 1 3 2 2 3
An overhead crane can be modelled as the beam system shown in Figure Q3. The beam of length L = 2.6 m is made of steel with Young's modulus, E = 202.4 x 10⁹ N/m². The second moment of area of the beam 1 = 3.7 x 10-4 m4. The stiffness of the spring, k₁ = 6.2 x 10³ N/m. The mass due to the load being lifted, m₁ = 3.4 x 10² kg. The beam mass is negligible compared with the load. You are required to find the equivalent stiffness of the beam, and then as your answer, to find the natural frequency of the system in Hz. Fill this answer in the box below. (Express your answer to 2dp) Flg. Q3 Answer: m₁ k₁

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS