A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3,700 N/m, that are attached to a threadedrod. The pitch of the threads is p = 1.5 mm.bВA-HangerFrameParallelKnurled nut -springsThreadedrodDThreaded,rodKnurled nutParallel springsTop view of the springsIf the weight is 63 N, how many revolutions of the nut are required to bring the pointer back to the mark?revolutions

For solution refer below images.

rod. The pitch of the threads is p1.5 mm. Hanger Frame Parallel Knurled nut- springs Threaded rod D Threaded rod Knurled nut Parallel springs Top view of the springs If the weight is 63 N, how many revolutions of the nut are required to bring the pointer back to the mark? Jrevolutions

rod. The pitch of the threads is p1.5 mm. Hanger Frame Parallel Knurled nut- springs Threaded rod D Threaded rod Knurled nut Parallel springs Top view of the springs If the weight is 63 N, how many revolutions of the nut are required to bring the pointer back to the mark? Jrevolutions

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The transformation from the last joint to the tool contains a rotation of 90 degrees. Select one: True False
Hello, I had submitted a previous question that I think got cut off. Cam someone help complete the worksheet please?
Please answer this machine design question. Keys and couplings. Would be very appreciated if the solution is clear for reviewing and practice
The stresses in a powered screw include: ___________________________. True or False with explanation For both shaft design and spring design, the running frequency should be at least two times lower than the first mode of natural frequency. True_ False__. The major stress in a spring comes from the direct shear. True_ False__. The natural frequency of a spring can be reduced by reducing the weight of the wire. True_ False__. Considering the contact fatigue of a gear, the wear factor should be higher than the gear factor. True_ False__. The pitch of the body coil can be calculated from the number of active coils and the critical length of the spring. True_ False__
For the given ball bearing find out the dynamic load value when the Equivalent load is 14836.2N and the Life of the bearing is 1238x10 revolutions. O a. 159305.06 O b. 139227.09 O c. 169418.59 O d. 80407.14 Finish attemp hp
Please help with all thank you!!
i li. O 9:00 Email address * baqir.hilal1306@student.uobabylon.edu.iq (Q1) A power screw with double start ASME thread is proposed to be used for cyclically raise and lower a load of 1000 lb at an axial velocity of 4 in/sec. It has three threads per inch and with thread outside diameter of 1.50 inches. The proposed mean collar radius is 1 inch. The starting and sliding friction coefficients for the screw and the collar are f_starting%3D0.06 and f_running=0.03 find: a. The staring and the sliding torque required to raise the load.b. Check the self-locking condition for the screw assembly. c. What is the power screw efficiency of the proposed assembly?d. If a special gear motor is to be used to drive this power screw assembly, what would be the minimum power and torque requirements for the drive motor?e. The length of the nut if the permissible bearing pressure is 725psi. Option 1 العربية الإنجليزية
Two single-row 02-series angular contact ball bearings with inner ring rotation are to be selected by a student for her Capstone project from Table 11-2 to support a radial load of 3.5 kN and axial load of 1.25 kN. The desired total machine reliability is 95%. The desired life of the bearings is 1 year of continuous operation in a machine operating at 900 rpm with light to moderate impact. Use the "manufacturer 2" Weibull values from Shigley Table 11-6 and equivalent radial load factors from Table 11-1. Fully specify the smallest bore size for these conditions.
80mm Y SK 60mm V 120 mm Gomm 40mm ->; Statics -2x Criven the shape above, Find The location of the Controid. Show all work.
How the sec (alpha) value is measured 29/2? Can you please describe the circled line in details.Thank you
I need help with 5,6 and 9.
You can select materials in the book name Design of Machine Elements by Faires.