C₂ located at a distance, y = 75mm, from the neutral find the normal strain &, if the wood is Douglas Fir, and the section Compute the net normal force acting on the top horizontal piece whi transmitted through the glue. 6-62. A box beam is constructed from four pieces of wood, glued together as shown. If the moment acting on the cross section is 10 kN-m, determine the stress at points A and B and show the results acting on volume elements located at these points.

C₂ located at a distance, y = 75mm, from the neutral find the normal strain &, if the wood is Douglas Fir, and the section Compute the net normal force acting on the top horizontal piece whi transmitted through the glue. 6-62. A box beam is constructed from four pieces of wood, glued together as shown. If the moment acting on the cross section is 10 kN-m, determine the stress at points A and B and show the results acting on volume elements located at these points.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Need answer and full solution ASAP. Thanks
T L 3. The wooden bar consists of two segments, each of length L. one segment has a square cross section of width d; the cross section of the other segment is a circle of diameter d. The working stress for the wood is 5MPa and he shear modulus is G = 0.5GPA. Using L = 0.6m and d = 50mm, determine the largest torque T that can be safely applied and the corresponding angle of twist for the bar. (Practice at Home)
A rectangular beam which is limited to 350 mm by 650 mm is reinforced at the compression side with As’ = 1,000 mm2and on the tension side As = 4,000 mm2. The beam has an effective depth of 510 mm and its neutral axis is located at 127.84 mm below the top of the beam. Assume steel in tension yields but that in compression does not yield. F’c = 35 MPa, β = 0.81, fy = 400 MPa. Steel covering on top is 50 mm. Determine stress of steel in compression. Determine the depth of compression stress block. Determine the moment capacity of the beam.
The forms are held in place with the ties between vertical braces spaced every 60 cm. the height h=28m. Assume that for the wet concrete the specific weight = 23.5 kn/m^3 and behave like liquid. 1. Obtain the force per unit meter length exerted on the forms. (2) What force is exerted on the bottom tie.
The joist AB used in housing construction is to be made from 8-in. by 1.5-in. Southern-pine boards. The design loading on each board is placed as shown in the figure below. The allowable bending stress for the wood is Jallow 1.5 and the allowable shear stress is Tallow = 180 psi. Assume that the beam is simply supported from the walls at A and B. (Figure 1) Figure 1 ▾of 1 8 in. 150 lb L 150 lb L 150 lb L 1.5 in. Determine the largest room width I that the boards can span. Express your answer to three significant figures and include the appropriate units. L = 32.0 Submit μA ft My Answers Give Up ? Incorrect; Try Again; 3 attempts remaining
Need asap pls. Thanks.
4. Find the maximum allowable value of P for the column. The cross- sectional areas and working stresses () are shown in Figure 3. 2P FIGURE 3 Steel: A=500 mm² Qw=120 MPa Timber: A=2000 mm² Ωw =12 MPa Timber: A=8000 mm² Ωw =16 MPa
Question # 1: The composite beam is made of steel (4) bonded to brass (B) and has the cross section shown. If the allowable bending stress for the steel is (sallow) st = 180 MPa, and for the brass (sallow) br = 60 MPa, determine the maximum moment (M) that can be applied to the beam Ebr 100 GPa, Est= 200 GPa B Question # 2: Determine the maximum shear stress acting at section a-a in the beam. 150 N/m m 8000 N Bla 1.5 m 1.5 m 50 mm 50 mm 200 mm 175 mm 200 mm -B 400 mm 75 mm 600 mm 75mm
Determine the maximum concrete and steel stresses at the point of maximum positive and negative moment. Fc'= 40 Mpa.
IVEN: A 20-ft beam is subjected to the distributed load show. 0.75 in. 6 in. -3 kip/ct A B K-8ft →→ 12 ft SOLUTION: TOT 12 in. Beam Cross Section 0.75 in -0.5 in. A S B FIND: a. The bending stress at A. b. The bending stress at B.
The beam shown here is made of wood with an allowable shear stress of τall = 1100 psi. If PB = 5 kips, determine the maximum allowable force PC that can be applied on the structure before the beam fails in shear.[LAB= 2 ft, LBC= 2 ft, LCD= 1.5 ft, b = 1.25 in., h = 7 in.] Determine the maximum value of the first moment of area (Q) for the beam. (in^3) Determine the maximum allowable force at C (PC) that can be applied on the structure before it fails in shear. (kips)
Put detailed solution and free body diagram. The topic is shear and bearing stresses.