4cm 12 cm 1- A wooden beam having a span length of 3m is built with three timber parts connecting by glue and supported as shown in the figure. Knowing that the allowable stresses for the material of the beam are Tall = 0.8 MPa, Tall = 14 MPa and safety shear stress for the glue is Tall,glue = 0.4 MPa, 3m 4cm a- Find the load q that can be safely carried by the beam, b- Using the q value you obtained, draw the normal and shear stress diagrams in the most critical section of the beam. glue

4cm 12 cm 1- A wooden beam having a span length of 3m is built with three timber parts connecting by glue and supported as shown in the figure. Knowing that the allowable stresses for the material of the beam are Tall = 0.8 MPa, Tall = 14 MPa and safety shear stress for the glue is Tall,glue = 0.4 MPa, 3m 4cm a- Find the load q that can be safely carried by the beam, b- Using the q value you obtained, draw the normal and shear stress diagrams in the most critical section of the beam. glue

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported wood beam, reinforced with steel plates, has the cross section shown. The beam carries a uniformly distributed load of 16 kN/m over the middle half of its 4-m span. If modular ratio is equal to 15, determine the largest bending stresses in the wood and steel. 96 mm 96 mm -200 mm 8 mm 240 mn 8 mm
Question # 1: The composite beam is made of steel (4) bonded to brass (B) and has the cross section shown. If the allowable bending stress for the steel is (sallow) st = 180 MPa, and for the brass (sallow) br = 60 MPa, determine the maximum moment (M) that can be applied to the beam Ebr 100 GPa, Est= 200 GPa B Question # 2: Determine the maximum shear stress acting at section a-a in the beam. 150 N/m m 8000 N Bla 1.5 m 1.5 m 50 mm 50 mm 200 mm 175 mm 200 mm -B 400 mm 75 mm 600 mm 75mm
A concrete floor slab 10e mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-020 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 8.003 in 3 decimal places =
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
1. Figure shows two wood members are joined together using a 60 degrees wood glue adhesive. Find the average normal and shear stress resisted in the plane of the connection. 25 mm 8 kN- 8 kN 60° 30 mm
Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)
2.6-22 A compression bar having a square cross section with sides b = 50 mm is subjected to load P. The bar is constructed from two pieces of wood that are connected by a glued joint along plane pq that is inclined at angle a = 35°. The allowable stress in the wood in compression is 11.5 MPa and in shear is 4.5 MPa. Also, the allowable stress in the glued joint in compression is 3.5 MPa and in shear is 1.25 MPa. Determine the maximum load P that can be applied to the bar.