A reinforced concrete beam has a width of 300 mm and an effective depth of 450 mm. The beam is reinforced with 6-32 mmØ bars at the bottom and 2-28 mmØ bars at 65 mm from the top. Use fc' = 34.5 MPa and fy = 345 MPa. Assume that the contribution of the compression steel may not be neglected and that the compression steel yields. 1. Which of the following gives the balanced steel ratio? B. 0.0489 D. 0.0597 2. Which of the following gives the depth of compression stress block? B. 140.94 mm D. 388.91 mm 3. Which of the following gives the nominal moment capacity of the beam? B. 398.4 kN-m A. 634.16 kN-m D. 713.4 kN-m C. 568.2 kN-m A. 0.0441 C. 0.0531 A. 127.58 mm C. 177.35 mm

A reinforced concrete beam has a width of 300 mm and an effective depth of 450 mm. The beam is reinforced with 6-32 mmØ bars at the bottom and 2-28 mmØ bars at 65 mm from the top. Use fc' = 34.5 MPa and fy = 345 MPa. Assume that the contribution of the compression steel may not be neglected and that the compression steel yields. 1. Which of the following gives the balanced steel ratio? B. 0.0489 D. 0.0597 2. Which of the following gives the depth of compression stress block? B. 140.94 mm D. 388.91 mm 3. Which of the following gives the nominal moment capacity of the beam? B. 398.4 kN-m A. 634.16 kN-m D. 713.4 kN-m C. 568.2 kN-m A. 0.0441 C. 0.0531 A. 127.58 mm C. 177.35 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Related questions

Q: The wooden beam shown is made by gluing together planks as shown. 8 kN/m Glue 80 mm 80 mm - NA 6 m…

A: Determine the maximum shear stress in the glue in kPa.

Q: a. The value of x from locating the neutral axis using Qtop Qbot in mm is [Select] b. The value of…

A: Answer (a) Consider 'x is a location of Neutral axis from the top as shown below Equate Qtop =…

Q: A rigid steel plate is supported by three posts of high-strength concrete each having an effective…

Q: The properties of the reinforced concrete beam are b = 304 mm, d = 475 mm, Ast = 1035 mm2, and Est /…

Q: A fully bonded aluminum shell and steel inner Outer core bar is axially loaded. Find the normal…

Q: An axial centric force of magnitude P= 460 kN is applied to the composite block shown by means of a…

A: Using equilibrium equation and compatibility equation

Q: The block is analysed in Cartesian system. The value of P is such that normal strain &=0. Modulus of…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

A reinforced concrete beam has a width of 300 mm and an effective depth of
ol
FOMBI
450 mm. The beam is reinforced with 6- 32 mmØ bars at the bottom and 2-28
mmØ bars at 65 mm from the top. Use fc' = 34.5 MPa and fy = 345 MPa.
Assume that the contribution of the compression steel may not be neglected and
that the compression steel yields.
1. Which of the following gives the balanced steel ratio?
B. 0.0489
D. 0.0597
2. Which of the following gives the depth of compression stress block?
B. 140.94 mm
D. 388.91 mm
3. Which of the following gives the nominal moment capacity of the beam?
B. 398.4 kN-m
A. 634.16 kN-m
D. 713.4 kN-m
C. 568.2 kN-m
A. 0.0441
C. 0.0531
A. 127.58 mm
C. 177.35 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Balanced steel ratio

VIEW

Step 3: Compression stress block depth

VIEW

Step 4: Moment capacity

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
How does a tensile stress differ from a compressive stress?
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.
According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
In Example Problem 12.1, a uniaxial composite material is made into a circular rod Vbith a 1.27-cm diameter from 70 volume percent continuous carbon fibers and 30 volume percent epoxy. The rod is subject to an axial force of 100,000 N. The composite matcrial in Example Problem 12.1 is to be replaced with a less expensive composite made of 70 volume percent continuous E-glass fibers and 30 volume percent epoxy. The elastic moduli are 5 GPa for the epoxy resin and 72.4 GPa fos the E-glass. (a) Compare the elastic modulus, composite strain, fiber and matrix stresses, and density of this composite with the carbon epoxy composite in Example Problem 12.1. Usc the density of UHM carbon, and assume the density of the epoxy is 1.2g/cm3 . (b) Can both the E-glass fiber and matrix withstand the applied force?