(c) Consider a cubic element with side length of 4 cm. The element has modulus of elasticity of 80 GPa and Poison's ratio of 0.3. If the element is subjected to equal forces in the x, y and z direction of 3 KN. Determine the volumetric strain and bulk modulus.

(c) Consider a cubic element with side length of 4 cm. The element has modulus of elasticity of 80 GPa and Poison's ratio of 0.3. If the element is subjected to equal forces in the x, y and z direction of 3 KN. Determine the volumetric strain and bulk modulus.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Need to determine the change in length of the bar due to its own weight, average normal strain over…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

Q: 2. A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are 0.40 x…

Q: The Strain along the width direction of the block subjected to 3 mutually perpendicular forces as…

Q: The strain at point A on the bracket has components P x = 300(10-6 ), Py = 550(10-6 ), gxy =…

A: Given data

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

Q: The state of strain on an element has components Px = -300(10-6), Py = 100(10-6), gxy = 150(10-6).…

A: Given Data: The x component of the normal strain is: εx=-300 X 10-6. The x component of the normal…

Q: Rigid bar ABCD is supported by two bars. There is no strain in the vertical bars before load P is…

A: (a) To find: The normal strain in bar 1. Given: The dimensions are L1=1900 mm, L2=1425 mm, a=190 mm,…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Given:The values are , , .The length of the bar is .The elastic constant is .Formula used:The…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

Q: The strain at point A on a beam has components Px = 450(10-6), Py = 825(10-6), gxy = 275(10-6), Pz =…

A: Given data

Q: The steel railroad increases its length when exposed to heat from 70°F to 95°F. The coefficient of…

A: Given data T1=70°F and T2= 95°F Thermal expansion coefficient = 11.7 ×10-6 (m/m°C) Find the strain

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Given that: Strain of the bar = ε = γy3E γ = specific weight = 2.1 lb/in3 L = length of the bar = 16…

Q: Calculate the elastic elongations that will occur in the x y axis on the adjacent object according…

A: given stress in x direction σx=-30 MPa (compression)stress in y direction σy=40Mpa (tensile)young…

Q: Determine the transverse strain in the x axis of the solid subjected to longitudinal tension. 4 cm 1…

A: Given:To find:The transverse strain in the x-axis of the solid subjected to longitudinal tension.

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Given:The values are , , .The length of the bar is .The elastic constant is .Formula used:The…

Q: The strain at point A on the pressure-vessel wall has components Px = 480(10-6), Py = 720(10-6), gxy…

A: Given: The normal strain in the vertical plane is PX=480×10-6. The normal strain in the horizontal…

Q: The Strain along the length direction of the block subjected to 3 mutually perpendicular forces as…

A: Given , Px is positive , Py and Pz are negative

Q: A sheet of steel is stretched biaxially in the xy-plane. The strains in the sheet are described…

Q: The strain at a point is 780x10-s in the x, 400x10-6 in the y and -500x106 in the z direction.…

Q: A thin metal alloy plate is loaded by biaxial stress (2 directions) given by 8000 psi in the x…

Q: 2. A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are 0.40 x…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Given data: γ=2.0 lb/in3y=2.8 inL=14 inE=20000 ksi Need to determine the change in length of the bar…

Q: A rectangular titanium plate has the following dimensions. a = 20 mm, b = 15 mm, and c=5 mm.…

Q: The 45° strain rosette is mounted on the surface of a shell. The following readings are obtained for…

A: Given that,εa=-200×10-6εb=300×10-6εc=250×10-6Here,εx=εc=250×10-6εy=εa=-200×10-6

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

Q: 3. Determine the stress and strain in the cable on the upper beam

Q: A thin polymer plate PQR is deformed such that corner Q is displaced downward a distance L = 0.10…

Q: Using the method of superposition and the figure, determine the strain at C (Vc). Include in your…

A: Given data, Applied UDL is w = 4 kips/ft Applied point load at C is P = 25 kips Length of the beam,…

Q: The truss ABC shown in the figure is subjectedto a horizontal load P at joint B. The twobars are…

A: Given Load = P Angle = 60° Find Strain energy, U Horizontal displacement

Q: After load P is applied to the pin-connected structure, a normal strain of = +650 μe is measured in…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

A: Given that: strain = ε = γy3E γ = 2.3 lb/in3 y = 2.4 in L = 6 in E = 24000 ksi It is required to…

Q: The principal plane stresses and associated strains in a plane at a point are s1 = 36 ksi, s2 = 16…

A: Given: The values of principal stresses are s1=36 ksi and s2=16 ksi. The values of strains are…

Q: One end of a aluminum rod of radius R = 9.4 mm and length L = 79 cm is held in a vise. A force of…

A: Given :- Rod radius, R = 9.4 mm = 9.4×10-3 m Length of rod, L = 79 cm = 0.79 m…

Q: The elastic portion of the stress–strain diagram for an aluminum alloy is shown in the figure. The…

A: Young’s modulus can be determined from graph as

Q: A cylindrical rod has initial dimensions of length ? = 4 m and radius ? = 1 cm. When the rod is…

A: Given data: The external force, P = 200 kN. The change in length, L'=4.024 m. The change in radius,…

Q: 2. A circular steel bar with with a diameter of 3 in and length of 2 m is subjected to an tensile…

A: Given data: d=3 in=0.0762 mL=2 mF=80 kNG=200 GPav=0.32 Need to determine the change in length and…

Q: Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear…

A: Plot the diagram from the values given in the table, As given, the curve is linear between the…

Q: In a hydraulic press a 690-liter volume of oil is subjected to a 6666-psi pressure increase. If the…

A: Given pressure change = 6666 psi = 453.5944 atm volume v= 690 litres compressibility of oil = 2.0 *…

Q: A pipe is subjected to a tension force of P = 70 kN. The pipe outside diameter is 32 mm, the wall…

Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…

Q: This course EHide blocks If a rubber material is deformed as shown in the following figure,…

Q: Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a…

Concept explainers

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.

Question

(c) Consider a cubic element with side length of 4 cm. The element has modulus of elasticity of
80 GPa and Poison's ratio of 0.3. If the element is subjected to equal forces in the x, y and z
direction of 3 KN. Determine the volumetric strain and bulk modulus.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular bar of length L has a slot in the central half of its length. The bar has width b, thickness t, and elastic modulus E. The slot has width b/3. The overall length of the bar is L = 560 mm, and the elastic modulus of the material is 68 GPa. If the average normal stress in the central portion of the bar is 210 MPa, calculate the overall elongation δ of the bar.
Determine the total strain energy and total potential energy in terms of the Prandtl stress function for torsion in a bar of length L and general cross-section A.
QUESTION 2 The rigid bar ACE is supported by two steel rods AB and CD (Esteel = 200 GPa) with the cross sectional areas of each rod is given as shown in Figure Q2. (a) Determine the position d of the 30 kN load so that the average normal stress in each rod is the same. (b) Find the strain in rod CD, ɛcD (c) Determine the horizontal displacement of point E 1.2 m ACD = 600 mm? 0.8 m E 30 kN AAB = 900 mm2 d B 1.8 m Figure Q2
The stresses in a 2-D rectangular steel body (E = 200 GPa, v=0.32) are xx = -A(L - x)y, and oxy = A(h² - 4y²); other stress components are zero. Here, L represents length and h is height. What is the strain component y xy A - (h² - y²) 8E O A A 8G - (h²-x²) - (h²-x²) 8E А A= (h²-y:²) 8G ?
The elastic portion of the tension stress–strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gage length of 2 in. and a diameter of 0.5 in. If the applied load is 10 kip, determine the new diameter of the specimen. The shear modulus is Gal = 3.811032 ksi.
1.Determine the total extension of the composite spring when subjected to the maximumload.2.Calculate the total strain energy in the spring assembly.
The vertical steel rod has a constant diameter of 32 mm and a length of 400 mm. is hanged from a rigid fixing. A mass is gently placed onto a collar which is attached to the lower end of the rod. The strain energy stored in the steel is 0.400 x 10-³. If Esteet = 209 GPa, 1.1 Determine the gradually applied load and magnitude of the mass. 1.2 Calculate the maximum stress in the rod when gradually applied. 1.3 Determine the magnitude of the mass when the mass is suddenly applied. 1.4 Calculate the extension of the rod when suddenly applied.
A 2.5 m long steel rod has a cross-sectional area of 0.35cm^2. The rod is hung from one end of the support structure and then a 600 kg winch is hung on the lower end of the rod. Determine: A. The stress(F/A) B. The strain
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.3 lb/in.³ is the specific weight of the material, y = 0.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 8 in. is the length of the bar, and E = 23000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar.
A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rods (1) is 4150 μm/m. Assume initial rod lengths of L₁ = 1,250 mm and L2 = 2,000 mm. Determine the normal strain in rod (2). (1) 4₁ Rigid bar (2) O 2849 μm/m O 3261 µm/m O 3071 µm/m O 3584 µm/m O 2594 μm/m B P L₂ C (1)
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 3.0 lb/in.³ is the specific weight of the material, y = 6.3 in. is the distance from the free (i.e., bottom) end of the bar, L = 21 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) avg (c) Emax i x10-6 in. με με
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.1 lb/in.³ is the specific weight of the material, y = 2.0 in. is the distance from the free (i.e., bottom) end of the bar, L = 5 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) 8 = i (b) avg (c) Emax = i x10 in. με με