2. A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are 0.40 x 10 - in the x direction and 0.30 x 10 in the y direction, determine the stresses in the x and y direction. Also, determine the strain in the z direction. The modulus of elastic and Poisson's ratio of copper is 110 GPa and 0.35 respectively. 3. If the copper in no. 2 is changed into steel with the same dimensions and with a modulus of elasticity of 200 GPa and a Poisson's ratio of 0.30, determine the strains in all direction if the same stresses in no. 2 where to be applied to the steel. €, E,

2. A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are 0.40 x 10 - in the x direction and 0.30 x 10 in the y direction, determine the stresses in the x and y direction. Also, determine the strain in the z direction. The modulus of elastic and Poisson's ratio of copper is 110 GPa and 0.35 respectively. 3. If the copper in no. 2 is changed into steel with the same dimensions and with a modulus of elasticity of 200 GPa and a Poisson's ratio of 0.30, determine the strains in all direction if the same stresses in no. 2 where to be applied to the steel. €, E,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

None
A rectangular titanium plate has the followingdimensions. a = 20 mm, b = 15 mm, and c=5 mm. Uniformly distributed tensile forces of 7.50 kN act in the z direction. Determine the strains in the x, y, and z directions. Let E = 120 GPa, and v = 0.35.
I need correct answer Nd fast ( handwritten)
P
A steel cable is used to support an elevator cage at the bottom of a 2100-ft-deep mineshaft. A uniform normal strain of 240 μin./in. is produced in the cable by the weight of the cage. At each point, the weight of the cable produces an additional normal strain that is proportional to the length of the cable below the point. Assume D = 2100 ft and d = 500 ft. If the total normal strain in the cable at the cable drum (upper end of the cable) is 790 μin./in., determine (a) the strain in the cable at a depth of 500 ft. (b) the total elongation of the cable. Drum Cable Answers: (a) ε = (b) 8 = i i d D Elevator cage X uin./in. in.
A strain gage is mounted to the outer surface of a thin-walled boiler. The boiler has an inside diameter of 1820_mm and a wall thickness of 18 mm, and it is made of stainless steel [E = 179 GPa; v = 0.3]. Determine: (a) the internal pressure in the boiler when the strain gage reads 210 µɛ. (b) the maximum shear strain in the plane of the boiler wall. (c) the absolute maximum shear strain on the outer surface of the boiler. Answers: (a) p = i MPа. (b) Ymax in-plane = i prad. (c) Yabs max i prad. =
A steel cable is used to support an elevator cage at the bottom of a 1900-ft-deep mineshaft. A uniform normal strain of 240 pin./in. is produced in the cable by the weight of the cage. At each point, the weight of the cable produces an additional normal strain that is proportional to the length of the cable below the point. Assume D = 1900 ft and d = 500 ft. If the total normal strain in the cable at the cable drum (upper end of the cable) is 780 μin./in., determine (a) the strain in the cable at a depth of 500 ft. (b) the total elongation of the cable. Drum Cable Answers: (a) ε = (b) 8 = i i d Elevator cage D X pin./in. in.
Deformed length of the elongated diagonal.
Figure shows a strain rosette that is attached on the surface of a production equipment. The strain readings are εa = -200(10^-6), εb = -65(10^-6) and εc = 130(10^-6).i) Determine the in-plane principal strains and sketch the strain element.ii) Determine the maximum in-plane shear strain and sketch the strain element.iii) What is the angle of orientation (with respect to x-axis) that leads to εx’ = 0?
A thin polymer plate PQR is deformed such that corner Q is displaced downward a distance L = 0.10 in. to new position Q' as shown. Determine the magnitude of the shear strain at Q' associated with the two edges (PQ and QR). P 25 in. 6862 μrad 8014 μrad O 7358 μrad O 4241 urad O 8668 μrad 4 in. R 10 in. X
The strain rosette shown was used to obtain normal strain data at a point on the free surface of a machine component. Given the values = -165 µμe, e = -155 μe, e = 50 μe, E = 10,600 ksi, and v=0.33, determine (a) the stress components o,,o,, and ry at the point. (b) the principal stresses and the maximum in-plane shear stress at the point; on paper, show these stresses on an appropriate sketch that indicates the orientation of the principal planes and the planes of maximum in-plane shear stress. (c) the magnitude of the absolute maximum shear stress at the point. 45° 45°
Determine the deformed length of the elongated diagonal