The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.0 lb/in.³ is the specific weight of the material, y = 2.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 14 in. is the length of the bar, and E = 20000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) Eavg= i (c) Emax = i x10-6 in. με με

The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.0 lb/in.³ is the specific weight of the material, y = 2.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 14 in. is the length of the bar, and E = 20000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) Eavg= i (c) Emax = i x10-6 in. με με

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A strain gauge is used to measure the shear strain on a shaft during torsional loading. The strain gauge is mounted such that it measures strain at an angle of 45° to the longitudinal axis of the shaft. The shear strain in the shaft is determined: a. as the strain measured by the strain gauge O b. by dividing the strain measured by the strain gauge by the shear modulus O c. None of these options O d. as twice the normal strain determined by the strain gauge.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30800 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.78 in.2 and bar (2) has a cross-sectional area of 0.32 in.2. After load P is applied, the strain in bar (1) is found to be 610 μεμε. Assume L1=50 in., L2=76 in., a=28 in., b=21 in., and c=22 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
1) An airplane's weight change is determined by reading the strain gauge A mounted on the plane's aluminum wheel strut. Before the plane is loaded, the strain gauge reading in the strut is &₁ = 0.00100 in./in., whereas after loading &2 = 0.00243 in./in. Determine the change in the force on the strut if the cross-sectional area of the strut is 3.5 in². and E = 10(10³) Ksi. O
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.07 in. If the length of bar (1) is L₁-41 in, determine the average normal strain in bar (1). Assume that a-135 in, b-39 in, and c-0.15 in a b C Rigid bar 4 Part 1 * Incorrect Determine the distance that end A of the rigid bar moves downward, if end C moves upward by 0.07 in Answer: in VA i 00361
A tri-axial state of stress, σx , σy, and σz ,exists in a steel machine part. For steel, E = 200GPa and ν = 0.3. Determine the normal strain in the x-direction if σx = 100MPa, σy = 35MPa, σz = 70MPa. Determine the dilatation. Determine the modulus of rigidity.
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.55 in., -0.17 in.). Assume a = 10 ft, b = 20 ft, c = 7 ft, and d = 14 ft. Determine the normal strain in each bar. Answer: EAB || A EBC= i P a (1) y B με με b (2) C d
The bar ABC in the figure consists of two cylindrical segments. The material of the bar has the stress-strain diagram shown. Calculate the strain in segment AB caused by the 60-kN axial load. 50 50mm 40 40mm 30 60 kN 60 kN 20 10 B 500mm 400mm 0.0000 0.0005 0.010 0.015 0.020 0.025 0.030 D.035 D.040 STRAIN SSHELS
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.06 in. If the length of bar (1) is L₁ = 51 in, determine the average normal strain in bar (1). Assume that a = 135 in., b=32 in., and c = 0.06 in. 4₁ 1 a Rigid bar B b
When an axial load is applied to the ends of the bar shown, where L₁ = 30 in. and L₂ = 80 in., the total elongation of the bar between joints A and C is 0.100 in. In segment (1), the normal strain is measured as 1700 µin./in. Determine the normal strain in segment (2) of the bar. A (1) L₁ 662 μin./in. O 784 μin./in. O 373 μin./in. O 719 μin./in. O 613 μin./in. B (2) L2
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.3 lb/in.³ is the specific weight of the material, y = 0.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 8 in. is the length of the bar, and E = 23000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar.
A rigid steel bar is supported by three rods as shown. There is no strain in the rods before the load P is applied. After load P is applied, the normal strain in rods (1) is 4150 μm/m. Assume initial rod lengths of L₁ = 1,250 mm and L2 = 2,000 mm. Determine the normal strain in rod (2). (1) 4₁ Rigid bar (2) O 2849 μm/m O 3261 µm/m O 3071 µm/m O 3584 µm/m O 2594 μm/m B P L₂ C (1)
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 3.0 lb/in.³ is the specific weight of the material, y = 6.3 in. is the distance from the free (i.e., bottom) end of the bar, L = 21 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) avg (c) Emax i x10-6 in. με με