An airplane's weight change is determined by reading the strain gauge A mounted on the plane's aluminum wheel strut. Before the plane is loaded, the strain gauge reading in the strut is &₁ = 0.00100 in./in., whereas after loading &2 = 0.00243 in./in. Determine the change in the force on the strut if the cross-sectional area of the strut is 3.5 in². and E = 10(10³) Ksi. O

An airplane's weight change is determined by reading the strain gauge A mounted on the plane's aluminum wheel strut. Before the plane is loaded, the strain gauge reading in the strut is &₁ = 0.00100 in./in., whereas after loading &2 = 0.00243 in./in. Determine the change in the force on the strut if the cross-sectional area of the strut is 3.5 in². and E = 10(10³) Ksi. O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rods A and B having a tensile stress of 400 N/mm², determine the diameter so that they can support the load shown. Then calculate the change in length and strain in each bar if (E=200000 MPa) (L=2 m)
After load P is applied to the pin-connected structure, a normal strain of = +650 µe is measured in the longitudinal direction of member (1). The cross-sectional area of member (1) is A₁ = 0.6 in.2, its elastic modulus is E₁ = 31000 ksi, and its yield strength is 33 ksi. Assume a=6.25 ft, b=7.75 ft, c=4.5 ft, and d=3.75 ft. (a) Determine the axial force in member (1), the applied load P, and the resultant force at pin B. (b) The ultimate shear strength of the steel pins is 52 ksi. Determine the minimum diameter for the pin at B if a factor of safety of 2.2 with respect to the ultimate shear strength is required. (c) Compute the factor of safety for member (1) with respect to its yield strength. (1) a D Answer: 0₁ = 1.6377 B (a) Determine the axial stress o, in member (1). ksi. b
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 2.3 lb/in.³ is the specific weight of the material, y = 2.4 in. is the distance from the free (i.e., bottom) end of the bar, L = 6 in. is the length of the bar, and E= 24000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) avg (c) Emax || MI Mi x10-6 in. με με
1-A round member having a diameter of 3cm experience an axial load of 10KN. Two strain gauges are mounted on the member, one measuring an axial strain of 600 micro-strain and the other measuring a lateral strain of -163 micro-strain. The modulus of elasticity in GPa is Choose... The Poisson ratio is Choose... + The stress in MPa is Choose... + Next page
2. ! SHOW FULL SOLUTION ! * use THERMAL STRESS AND STRAIN FORMULAS *use DATA GIVEN BELOW
Determine the equivalent state of strain on an element at the same point oriented 30∘∘ clockwise with respect to the original element. ϵx′, ϵy′,γx′y′ =
A strain gauges system mounted at a point on a structural member that is subjected to a multiaxial stress, where we have the following readings: &x = 7.820 x10+; Ey = -8.680x10¹4;&z= 3.200 x104; Vxy = 2.112 x10-³; Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Poisson's ratio y = 0.32 and shear modulus G = 37.9 Gpa; E= Ox= Gy = Txy = 27.1 GPa 75 MPa 77 GPa 80 MPa -50 MPa 75 MPa -50 MPa 100 MPa 100 GPa 100 MPa 40 MPa 40 MPa 40 MPa -50 MPa 80 MPa
The elastic portion of the stress–strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm andagagelengthof50.8mm.IfaloadofP=60kNisapplied to the specimen, determine its new diameter and length. Take n = 0.35.
2) The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gauge length of 50 mm and a diameter of 12.5 mm. When the applied load is 45 KN, the new diameter of the specimen is 12.48375 mm. Compute the shear modulus (Gal) for the aluminum. σ (MPa) 500 71 0.00614 € (mm/mm)
6. Airplane components often have a “stressed skin" construction, which consists of a thin sheet of aluminum in tension connected to the structure with rivets (i.e. pins that go through circular holes). a. If the aluminum skin is subject to a far-field biaxial tension of σ = 100 MPa and has a yield strength of σ = 210 MPa, will the rivet cause the sheet to yield? b. What is the strain through the thickness (z-direction) at the top-most edge of the hole? What does this mean is happening to the plate at that point? c. If a crack of length a = 1 mm forms at the side of the hole, will the plate fracture? How about if the crack is a = 3 mm? Take the aluminum to have a fracture toughness of K₁c = 15 MPa√m, and take the geometric stress concentration factor to be Y = 1.12. 50 = a
The rigid body ABC is connected by two links and is exerted by force P as shown aside. If the normal strain in link BE is 1x10 the normal strain in link AD is: D E B 2 m 1m PV Select one: -3 O a. 4.5x10 -3 O b. 1.5x10 O c. 1.0x10 -3 O d. 3.0x10 O e. 2.5x10 O f. None 3 m 1.5 m
The wire AB is unstretched when 8 = 45°, If a force is applied downward to end A of the bar AC, which causes e = 485°, then the average normal strain in the wire AB is equal to 23 O 0.0287 O D.0757 O 00779 O 00398 O 0.0697