The strain gauge is placed on the surface of a thin-walled steel boiler as shown The gauge is 0.5 in long and it elongates 0.17(103) in when a pressure is applied. The boiler has a thickness of 0.5 in and inner diameter of 60 in Est=29(10³) ksi, vat = 0.3 (Figure 1) Figure 0.5 in. < 1 of 1 60 in. > Determine the pressure in the boiler. Express your answer using three significant figures and include the appropriate units. p= Value Submit Part B Request Answer Ymax in plane= Submit Determine the maximum x y in-plane shear strain in the material Express your answer using three significant figures. Πνῇ| ΑΣΦ 11 vec Units Request Answer ? ?

The strain gauge is placed on the surface of a thin-walled steel boiler as shown The gauge is 0.5 in long and it elongates 0.17(103) in when a pressure is applied. The boiler has a thickness of 0.5 in and inner diameter of 60 in Est=29(10³) ksi, vat = 0.3 (Figure 1) Figure 0.5 in. < 1 of 1 60 in. > Determine the pressure in the boiler. Express your answer using three significant figures and include the appropriate units. p= Value Submit Part B Request Answer Ymax in plane= Submit Determine the maximum x y in-plane shear strain in the material Express your answer using three significant figures. Πνῇ| ΑΣΦ 11 vec Units Request Answer ? ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The state of strain at the point on the arm in Figure Q10 has components ϵx = 200.5 micro-strain, ϵy = 324.4 micro-strain, and γxy = 220.6 micro-strain (1 micro-strain = strain×10-6). Figure 10 Calculate the maximum principal strain. Express your answer in micro-strains. Report your answer to 1 decimal place.
A strain gauge is used to measure the shear strain on a shaft during torsional loading. The strain gauge is mounted such that it measures strain at an angle of 45° to the longitudinal axis of the shaft. The shear strain in the shaft is determined: a. as the strain measured by the strain gauge O b. by dividing the strain measured by the strain gauge by the shear modulus O c. None of these options O d. as twice the normal strain determined by the strain gauge.
3) A thin-walled cylindrical pressure vessel of diameter of 1.5 m is subjected to an internal pressure that varies continuously from p_min= 0.8MPa to p_max = 4 MPa. Determine the pressure vessel thickness, t, if the pressure vessel is made from steel with an ultimate strength S_u=400 MPa, a yield strength S_y=300MPa, and an endurance limit S_n-150MPa and a safety factor of two is desired. Use Modified Goodman and the maximum normal stress theory.
A 60 ̊ strain rosette measures the following strain at a point on the aluminum skin of an airplane. ε0 = 160 ×10-6 m/m, ε60 = -220 ×10-6 m/m and ε120 = 360 ×10-6 m/m. Using E= 10 ×106 psi and v = 0.3, Determine the principle stresses and the maximum in-plane shear stress.
A spherical pressure vessel has an inside diameter of 4 m and a wall thickness of 15 mm. The vessel will be constructed from structural steel [E = 200 GPa; v = 0.29] that has a yield strength of 203 MPa. If the internal pressure in the vessel is 1930 kPa, determine the factor of safety with respect to the yield strength. 1.58 2.21 O 1.30 1.45 O 1.13
1) An airplane's weight change is determined by reading the strain gauge A mounted on the plane's aluminum wheel strut. Before the plane is loaded, the strain gauge reading in the strut is &₁ = 0.00100 in./in., whereas after loading &2 = 0.00243 in./in. Determine the change in the force on the strut if the cross-sectional area of the strut is 3.5 in². and E = 10(10³) Ksi. O
From the stress states in a Cartesian coordinate system, the following tensors are obtained:σxy = [100-100-100-800)]. Determine and graph the principal stresses and the directions associated with them using the mohr's circle. determine and graph the maximum shear stresses graph the possible failure planes finally, what is the value of the maximum tangential stress and in what orientations does it take place?
5. In the CN Railwayproject,steel railroad rails of 9.5meters long are to be installed.If the modulus of elasticity of steel is207GPa, and if the lowest temperature considered is 18°C and a maximum temperature of 36°C is designed for, determine the clearance between the rails such that adjoining will just touch at maximum design temperature. Assume α for steel is 11.6 x 10-6/°C
The strain gauge is installed on the material for use, ②according to the change of the load material ①, the final change of the circuit ③.② Increase or decrease according to the tension or compression environment. This principle is because the ④ and ⑤ of the strain gauge change according to the change of the material ①. ① ② ③ ④ ⑤
A strain gauges system mounted at a point on a structural member that is subjected to multiaxial stress, where we have the following readings: Ex = 3.079 x1o-3. ; Ey = -3.471 x10-3; Ez = 1.207 x10-3; yxy = 3.743 x10-3; Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Young's modulus E = 70 Gpa and shear modulus G = 26.7 Gpa;
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression vy/3E where y = 2.3 lb/in.³ is the specific weight of the material, y = 0.8 in. is the distance from the free (i.e., bottom) end of the bar, L = 8 in. is the length of the bar, and E = 23000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar. (c) the maximum normal strain in the bar.
The piston-cylinder assembly above has a wall thickness of 0.125" and an outer radius ro= 2 in. If the internal gauge pressure is 1.2 ksi, determine the maximum normal stress in the piston wall. 18 ksl O9 ksi 36 ksi N/A (this does not meet the criteria of a "thin-walled" pressure vessel)