Bearing plate is design to distribute the reaction of W12x65 with a span length of 12 ft center-to-center of supports. The total service load including the beamweight is 15 kips/ft with Live load / Dead load ratio equals to 2. The beam is to be supported on RC walls with f'c =4,000 psi. For the beam, Fy = 50 ksi and= 36 ksi for the plate. Use LRFD. If {b = 8 inch and B = 14 inch, what is the minimum computed thickness of the bearing plate in inch? Express yourFyanswer in three decimal places.

Answered: Image /qna-images/answer/a3424d91-8e0f-4df3-b8ca-82765b00c0c0.jpg

Answered: Bearing plate is design to distribute…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Similar questions

really really need asap please
Bearing P plate Let the allowable stresses in the post be ost=120MPaand oco=6MPA. Compute the maximum safe axial load P that may be applied. The moduli of elasticity are 200 GPafor steel and 14 GPafor a concrete. Each steel bar has cross-sectional area of 900mm2. Steel - Concrete - 300 mm 300 mm
1. For the Pratt bridge truss and the loading shown below, determine the average normal stress in member BE, knowing that the cross-sectional area of that member is 60 in². NN K 12-12--12--12--| 50 lips 50 kips 50. ips Figure 1 G xfone
AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. X+Y Properties of W 12 x 65 A 12323 mm2 - 134.11 mm ry 76.71 mm Fy- 248 MPa Determine the allowable compressive strength (kN).
I NEED ANSWER
W/FBD
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa
PLEASE DRAW AND LABEL PROPERLY THE FBD. THANK YOU. Use Portal Method From the frame loaded as shown. Solve the following: a. The shear at girder HI. b. The end moment at girder HI.c. The shear at girder EF.d. The end moment at girder EF.e. The moment at column C.
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below
Solve by LRFD (AISC ) masnual
Need urgent answer Don't provide wrong solution

SEE MORE QUESTIONS

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning