Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m &C 2 m 1380 2m

Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m &C 2 m 1380 2m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Details of a rectangular column are as follows: Column width along X-axis-250 mm Column Depth along the Y-axis-600 mm 8-25 mm diameter bars distributed equally along the longer sides. 10 mm diameter ties spaced at 10 mm on centers Concrete 28th day Compressive strength, fc;=20.7 MPa Reinforcing Steel yield strength, fy-415 MPa Assume that compression steel yields. a) Which of the following gives the nominal balanced load Pb (kN). A = 90.4 mm b) Which of the following gives the nominal axial load (kN) that the column n carry at an eccentricity of 200 mm along the X axis from the centroidal Y-axis.
Problem2. The compression member is shown in figure. Find the following: a. The Euler stress Fe. b. The buckling stress Fcr c. The design strength d. The allowable strength e. Does the member satisfactorily meet the design requirements? Why? HSS 8x 8x4 ASTM AS00, Grade B steel (Fy = 46 ksi) 15'
A simply supported wood beam, reinforced with steel plates, has the cross section shown. The beam carries a uniformly distributed load of 16 kN/m over the middle half of its 4-m span. If modular ratio is equal to 15, determine the largest bending stresses in the wood and steel. 96 mm 96 mm -200 mm 8 mm 240 mn 8 mm
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (ow) are shown in the figure. |2P Steel: A = 500 mm2 Ow = 120 MPa P Timber: 4P A = 2000 mm? Ow = 12 MPa Concrete: A = 8000 mm? O = 16 MPa
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
S9. Knowing that the allowable normal stress for the steel used is 150 MPa, select the most economical metric wide-flange beam to support the loading shown in Figure 9.0. 50 kN/m A D B -2.4 m- 0.8 m 0.8 m Figure 9.0 $10. Determine the average shearing stress in the web of the beam indicated and check whether the design obtained earlier for that beam is acceptable, knowing that the allowable shearing stress for the steel used is 110 MPa. Consider the beam of $9 above.
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
Asiacell lln. H.W. No.1 For the simply supported solid one way reinforced concrete slab shown in the figure below having a span of (L= 4m), check the following requirements using strength method: a- Slab thickness b- The spacing between reinforcement for main and shrinkage reinforcement c- The actual reinforcement with minimum reinforcement d- Calculate ultimate resisted moment that can be withstand by the slab e- Determine the ultimate uniformly distributed load carried by slab. f = 25 N/mm2 fy=420 N/mm² + 10mm@s00mm shrinkage h=200mm -L=4m- $12mm@200mm main
Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)