square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa

square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The size of the plates is 300 mm x 12 mm. Fy 248 MPa, Fn = 330 MPa and Fu = 400 MPa. Determine the following: (1) Design strength of the connection based on strength of plates. (2) Design strength of the connection based on shear strength of bolts. =0.65. (3) Design strength of connection based on bearing strength of bolts on the 12 mm plate. =0.75 12 mm P. mm O. O 300 mm 40 80
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
WELDED CONNECTIONS: THE BRACKET SHOWN IN THE FIGURE IS WELDED ON ONE SIDE OF A STEEL COLUMN WITH 800 mm OF 6 mm FILLET WELD. DETERMINE THE MAXIMUM SHEAR STRESS ON THE WELD.
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Please help with the problem below
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
a welded connection is in eqilibrium under the action of the four forces shown. Knowing that FA=8lbs and FB= 16lbs, determine the magnitudes of other two forces *3dec places all final
I need the answer as soon as possible
compute Compute the Euler's Buckling load andGoverning Nominal Compressive strength based on AISC E3-2 or E3-3 (kips)
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear
Question 1: (Use NSCP 505.3 provisions and ASEP Steel Handbook for effective length factors) Use AISC Equation E3-2 or E3-3 and determine the nominal axial compressive strength for the following cases: a. L= 15 ft b. L=20 ft W10 × 33 A992 steel FIGURE P4.3-1