B. Add the necessary forwarding paths for the following instructions in thedatapath shown here.B1 add R3, R3, R42 sub R4, R2, R43 add R4, R5, R3Address>AddInstructionmemoryIF/IDReadregister 1Readregister 2WriteregisterWritedataRegisters Readdata 2Readdata16Sign-extendID/EXShiftleft 2Add AddresultZeroALU ALUresultEX/MEM-AddressWritedataDatamemoryReaddataMEM/WB

Name: B. Add the necessary forwarding paths for the following instructions
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: B. Add the necessary forwarding paths for the following instructions in thedatapath shown here.B1 add R3, R3, R42 sub R4, R2, R43 add R4, R5, R3Address>AddInstructionmemoryIF/IDReadregister 1Readregister 2WriteregisterWritedataRegisters Readdata 2Re

The datapath includes registers, ALU and interconnected bus that allows data to flow between them.…

Engineering

Computer Science

B. Add the necessary forwarding paths for the following instructions in the datapath shown here. B 1 add R3, R3, R4 2 sub R4, R2, R4 3 add R4, R5, R3 Lo-o! Address >Add Instruction memory IFAD Road register 1 Read regregisters Road 2 Write register Write data Read data 16 Sign 32 extend DEX Shin left 2 Adg Ass result Zero ALU ALL result EXMEM Address data Data memory Read MEMWB

B. Add the necessary forwarding paths for the following instructions in the datapath shown here. B 1 add R3, R3, R4 2 sub R4, R2, R4 3 add R4, R5, R3 Lo-o! Address >Add Instruction memory IFAD Road register 1 Read regregisters Road 2 Write register Write data Read data 16 Sign 32 extend DEX Shin left 2 Adg Ass result Zero ALU ALL result EXMEM Address data Data memory Read MEMWB

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Suppose we have the instruction Load 0000. Given memory and register R1 contain thevalues below:R130Memory Address Content0000 40...0010 30...0020 78...0030 55...0040 77...0050 84 Assuming R1 is implied in the indexed addressing mode, determine the actual value loaded into the accumulator using the following addressing modes: a. Immediateb. Directc. Indirectd. Indexed
Explain 1. Using 1-Address instructions 2.Using 2-Address instructions 3.Using 3-Address instructions
3. Suppose M8=x and M9=y. After each instruction has been executed, what is the content of the location indicated in column 3? Fill the contents in the table. Address M1 Content MMR M8 R1 MMR M9 R2 Locations Register 1 Register 2 Accumulator M7 Content М2 M3 ADD R1 R2 М4 МАМ M7 M5 HLT M7
Which memory address in Interrupt Vector Table (IVT) stores the higher byte of the segment part forthe beginning address of ISR that corresponds to ITC 15 H? Justify your answer with calculation. give diagram if needed
Identify the addressing modes used for the source and destination operands, and thencompute the physical address for the specified operand in each of the following instructions:(Assume all missing data.)1. MOV CX, [DI] (Source operand)2. MOV [BP]+BETA, AX (Destination operand)3. XCHG BX, [FF02] (Source operand)
2. Consider the initial value of register 5tl is Ox12345678 and the content of memory location Ox10010000 is OXABCD1234. Write the instructions if we want the content of register 5t1 to be as follows: a. OXABCD5678 b. Ox12340000 c. Ox00005678
In the event that an instruction is not accepted, it will write to VA page 30. In circumstances like these, it would be more efficient to employ a TLB that is handled by software rather than one that is maintained by hardware.
The NOR instruction is not part of the RISC-V instruction set because the samefunctionality can be implemented using existing instructions. Write a short assembly codesnippet that has the following functionality: s3 = s4 NOR s5. Use as few instructions aspossible. Write RISC-V assembly code for placing the following immediate constants inregister s7. Use a minimum number of instructions.a) 59b) -199c) 0xDDCBE289d) 0x11236BDF
In this case, every instruction gets its own data in a way that is completely separate from how the data of other instructions is obtained. We utilize: A Multiple Data/Instruction B Multiple Data/Instruction C Singular Data Single Inst D Singe Inst Multiple
For example, suppose an instruction is not accepted and VA page 30 is generated. A software-managed TLB can outperform a hardware-managed TLB in the following cases:
Datapath for the LDI Instruction 7 Recently we have been discussing the importance of the datapath and its relationship to the Register Transfer Notation and control signals need to execute instructions in the datapath. Answer the following questions about this specific What is the ML (or binary instruction) of this single instruction? Give your answer in hexadecimal. instruction: type your answer... LDI R4, data Where the label data is at address x3005, and the LDR instruction is at address x3000. What is the Register Transfer notation for this instruction? Remember to change the destination and source registers to the actual registers of the instruction. type your answer... List in order all the controls signals required to execute this instruction. You do not need to list the signals for fetching and decoding the instruction.