An AJMP instruction is in memory locations 1A24H and 1A25H. The label of this instruction will be directed begins in memory location 18B6H. How can be the destination address encoded? Hint: the opcode for AJMP instruction is 01H. A

Q: Question// calculate physical addressing mode for the following instruction MOVv AX,[BX].ALPHA if…

A: In the above instruction S=0200H, ALPHA=AB54H, and [BX]=900H are given. The data segment register…

Q: This is a MIPS single cycle processor. Please highlight the datapath of implementing the "Iw"…

A: MIPS single cycle processor- An instruction set architecture is an interface that defines the…

Q: Assume that the physical address of the instruction is (D6A92H) and the code 2 Bandwidth segment…

A: Memory addressing schemes:1. An Absolute Address, such as 04A26H, is a 20 bit value that directly…

Q: Q3: An instruction is stored at location 501 with its address field at location 502. The address…

A: Ans. For direct :Effective addrress =M[500] =501 For indirect : Effective address =M[M[500]] = 200…

Q: e instruction, Add #45,R1 does Adds 45 to the value of Rl and stores it in R1 Adds the value of 45…

A: Add #45, R1 is instruction for addition.

Q: In the instruction x = 8-5. The step of the machine cycle that responsible to read this instruction…

A: The solution to the given problem is below.

Q: If this Datapath is currently executing the instruction, LW $s1, -4($t1), register s1 contains the…

A: It is defined as the Operator at the heart of the control room with its latest fully integrated…

Q: Q:find the actual address for the following instruction assume X=A6 and ?=PC=8B79, LOAD X(PC), D…

A: The given data is. X = A6 PC = 8B79 The given instruction is: LOAD X(PC), D

Q: If the first instruction "LXI H, 1100H" is positioned at address 7000H in memory, at what address…

A:

Q: Please write corresponding MIPS assembly instruction to the right of MIPS machine instruction.

A: We have to Write the MIPS machine Instruction for the given assembly code. The assembly codes are…

Q: Which statement is correct about IN and OUT instructions of 8086 assembly language? a. OUT…

A: IN and OUT are mnemonics from 8086 which is used to send or receive data from the port.

Q: Write an instruction that loads the value -185 (in decimal) in x6. Answer: Write an instruction that…

A: This is a draft of the next release of the document describing the RISC-V user-level…

Q: When the CMP instruction sequence is executed, what is the final value for AL register? MOV AL, 25h…

A: The CMP instruction compares two operands. It is generally used in conditional execution.

Q: Q2: Calculate the physical address for the following instruction (MOV DX, [SI]) knowing that the…

A:

Q: An LC-3 assembly language program contains the instructions z LD R4, Y LD RS, Z The symbol table…

A: LC-3 Assembly instructions: Z  LD R4, Y       Y  LD R5, Z Symbol table entry for Z is x300A.

Q: A - Mention how do the following instructions differ 1- NEG & NOT 2- DIV & IDIV 3- AND & TEST 4- CMP…

A: A microprocessor is a computer processor that incorporates the functions of a central…

Q: Instruction : SUB Rd, Rs, Rt a. What are the values of control signals generated by the control in…

A: ALU: ALU stands for Arithmetic Logic Unit. It performs arithmetic and logic operations such as…

Q: If JMP 90 instruction reside at memory location OFCDA then, the memory * location of the next…

A: Solution:-

Q: Please answer using Kip Irvine Assembly Language for the x86 processor Using Shift Instructions to…

A: Solution(a) Multiplication of EAX by 16 is equivalent to shifting left by 4 bits. SHL EAX, 4…

Q: Execute the following instruction using zero address instruction. X=X*Y+Z/A-B*C+E*F *

A: The execution of the following Instruction using zero address instruction X=X*Y+Z/A-B*C+E*F  is…

Q: Find the pyhsical destination adress of last instruction below. MOV BX,0AAH MOV AX,1BBH MOV DS,AX…

A: MOV BX,0AAH will move data AA into register B MOV AX,1BBH will move data 1BB into register A…

Q: Write a single instruction that loads AX from address 200H and DS from 202H.

A: The answer is in step 2:

Q: Determine the value after the instruction (signed division). AX = 0020H DL = FCH IDIV DL Select…

A: Option D is correct .i.e FFF8H

Q: of 10H, of the instruction MOV AL. [BP+SI+10HJ. Which the name of A Q2:- (B) Find the result of the…

A: B)1111_111H+11001011011B =1111_11101001000+110010110110100001 =11101000111+110010110110100001…

Q: Which Insruction? Here is the data flow diagram for a particular instruction. The various values…

A:

Q: H\W: Assuming the SP-1236. Ax-2486. DI= 85c2 and Dx-5f93, show the content of the stack and the…

A: Given Data: SP = 1236H AX = 2486H DI = 85C2H DX = 5F93H   ADD AX,SP: Add values of AX and SP and…

Q: An ADD instruction stores a value 7308h at offset value 9F71h. If the computed address is 7CB31h,…

A: Given information:- Offset value = 9F71 h Computed address = 7CB31 h So, Initial address = Computed…

Q: When the CMP instruction sequence is executed, what is the final value for AL register ? MOV AL, 25h…

A: 1) The CMP instruction compares two operands. It is generally used in conditional execution. Its…

Q: You are given the following instruction: ADD AX, [10h] You are provided the following data: DS =…

A: We have some data provided in the question . Here we have the statement given as : ADD AX [10h] DS =…

Q: CMP INSTRUCTION HAS THE SAME FUNCTION AS Select one: O a. SUB INSTRUCTION WITHOUT SAVING THE RESULT…

A: CMP instruction The value of Operand2 is subtracted from the value in Rn by the CMP instruction.

Q: CMP INSTRUCTION HAS THE SAME FUNCTION AS Select one: a. SUB INSTRUCTION WITH SAVING THE RESULT IN…

A: Let us see the answer below.

Q: For the instructions below, assume the initial conditions shown for r3-r5 and the flags. Show the…

A: The ANDS instruction performs a bitwise AND operation between the values of r4 and r5, and stores…

Q: Explain what happens when the POP CX instruction executes. Make sure to show the physical addresses…

A: Stack is an area of memory for keeping temporary data. Stack is used by CALL instruction to keep…

Q: When the CMP instruction sequence is executed, what is the final value for AL register ? MOV AL, 25h…

A: CMP instruction is used to compare contents of the Accumulator with given register R.  CMP…

Q: What is the ALU operation for "SW" (store word) instruction? write to memory multiply subtract…

A: Sure, here is an introduction to the question:The "SW" instruction is a load/store instruction in…

Q: Write the instruction format for the jump instruction.

A: Introduction: Instruction format: The instructions that are given to a computer will cause it to…

Q: Using the mov.w instruction we copy the 16-bit word 0xB612 to the address 0x1C20. You do not need to…

A: We must take into account the endianness of the system (whether it is little-endian or big-endian)…

Q: The CMP instruction is used to compare 2 operands. You can use a jump instruction afterwards. True…

A: CMP instruction is used to compare 2 operands. we can use jump instruction afterwards. Syntax :- CMP…