Instruction : SUB Rd, Rs, Rt a. What are the values of control signals generated by the control in Figure I for the above instruction? b. Which resources (blocks) perform a useful function for this instruction? c. Which resources (blocks) produce outputs, but their outputs are not used for this instruction? d. Which resources produce no outputs for this instruction

Instruction : SUB Rd, Rs, Rt a. What are the values of control signals generated by the control in Figure I for the above instruction? b. Which resources (blocks) perform a useful function for this instruction? c. Which resources (blocks) produce outputs, but their outputs are not used for this instruction? d. Which resources produce no outputs for this instruction

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Because of this, the means by which one instruction acquires its input data are independent of the means by which another acquires its data. When used with a(n): A Combining sets of data with sets of instructions B An example of "multiple data, multiple instruction" C D is for "data alone," meaning there is just one instruction. One order, several results
There are two "backup" instructions for each instruction in a computer instruction set design, which is called orthogonality. Tell us whether this statement is correct or incorrect.
Please look at the question properly, it is asking for the machine code for the MIPS instruction below. Please write thorougly so I am able to understand it.
Fill in the following table showing the results of the indicated instructions, using the register values shown. Also, show the OF and CF values AFTER the instruction executes. Show all results in hexadecimal. Show OF and CF as 0 or 1.
4. Consider the following instruction: and $t0, $e5, $3 a. What are the values of the control signals generated by the control unit for the above instruction? RegDst Jump Branch MemRead MemtoReg MemWrite ALUSrc RegWrite
For the RISC-V assembly instructions below, what is the corresponding C statement? Assume that the variables f, g, h, i, and j are assigned to registers x5, x6, x7, x28, and x29, respectively. Assume that the base address of the arrays A and B are in registers x10 and x11, respectively. sub x30, x28, x29 slli x30, x30, 2 add x3, x30, x10 add x4, x30, x11 1w x30, 0 (x3) 1w x31, 0 (x4) add x30, x30, x31 sw x30, 16 (x11)
In this case, every instruction receives its own data, independent of how the data for other instructions is obtained. We make advantage of a: A Multiple Data/Instruction B Multiple Iterations of Data or Instruction C Singular Data Single Inst D Singe Inst Multiple
An instruction is stored at location 100 with its address field at location 101.The address field has value 200. A processor register R1 contains the number 300. Evaluate the effective address if the addressing mode of the instruction is A. Direct B. Immediate C. Relative D. Register Indirect E. Index with R1 as the index Register
In this implementation, each instruction is provided with its own data independently of how other instructions acquire theirs. We insert a(n): A Multiple Input/Output B The Case of Many Pieces of Information or Directions C Unique Information Only One D Several Insts From One
Computer Science Write an instruction that divides the content of register ($t1) by 2, and puts the result in the register ($s1) using shift operations.
The fetch-execute cycle can be simply described by the following algorithm: the program counter increment the end repeat Blank # 1 Blank # 2 Blank # 3 Blank # 4 Blank # 5 Blank # 6 forever the instruction pointed to by the program counter to point at the next instruction the instruction the instruction A A/ A A/
Computer Science - Assembly language code: Q1. A) A microprocessor is wired into a sensing control circuit so that the memory locations 42 and 43 each contain the values 0 or 1. Memory location 50 is connected to a light switch. When the value in 50 is 1 the light is on and when it is 0 the light is off. Write a program to switch on the light on when the values in locations 42 and 43 are both 1, and to switch off the light when the values in locations 42 and 43 are both 0. Only use the ARM assembly language instructions, MOV, JMP and JNZ. Assume that the MOV instruction updates the flags with the status register.