Assume you are executing an instruction as following, ADD $s0, $t0, $t1 Draw the datapath for this instruction. Assume each datapath stages take 1-cycle to finish. How long will it take to finish the execution? Show which component/register is busy in different cycles. Assume you are staring the instruction execution at cycle 0. Mark the progress of execution in datapath with alphabets (A, B, C, ……).

Q: Assume that the physical address of the instruction is (D6A92H) and the code 2 Bandwidth segment…

A: Memory addressing schemes:1. An Absolute Address, such as 04A26H, is a 20 bit value that directly…

Q: e instruction, Add #45,R1 does Adds 45 to the value of Rl and stores it in R1 Adds the value of 45…

A: Add #45, R1 is instruction for addition.

Q: In the instruction x = 8-5. The step of the machine cycle that responsible to read this instruction…

A: The solution to the given problem is below.

Q: Write the register transfer operations for the following pression. ( A=C/(B-C*2)

A: Summary: - Hence we discussed all the points.

Q: Each item in the interrupt vector table represents a distinct collection of data.

A: Interrupt vector table (IVT) is a fundamental concept in computer architecture, particularly in…

Q: Assume you are executing an instruction as following, ADD $s0, $t0, $t1 Draw the datapath for this…

A: The five data path stages are: Instruction fetch Instruction decode Execution-ALU Memory access…

Q: When the CMP instruction sequence is executed, what is the final value for AL register ? MOV AL, 25h…

A: Answer is in step-2.

Q: Draw the datapath for store instruction. Give clear explanation too.

A: Solution: The datapath for the store instruction. New pc value is computed instruction is read two…

Q: Execute the following instruction using one-address instruction format. R=(X+Y*Z)/(A-B*C+G*D)

A: Let's understand step by step :   One address instruction format : In one address instruction format…

Q: Give any 5 addressing modes which do not use the address given inside the  instruction to fetch the…

A: Given: Give any 5 addressing modes that do not use the address given inside the instruction to fetch…

Q: Instruction : SUB Rd, Rs, Rt a. What are the values of control signals generated by the control in…

A: ALU: ALU stands for Arithmetic Logic Unit. It performs arithmetic and logic operations such as…

Q: Execute the following instruction using zero address instruction. X=X*Y+Z/A-B*C+E*F *

A: The execution of the following Instruction using zero address instruction X=X*Y+Z/A-B*C+E*F  is…

Q: Describe the stages involved in the fetch-decode-execute cycle in detail. Your explanation should…

A: Introduction: Fetch-dee-execute cycle steps code-execute cycle is a standard process that describes…

Q: Which Insruction? Here is the data flow diagram for a particular instruction. The various values…

A:

Q: Computers use addressing mode strategies for Specifying rules for modifying or interpreting address…

A: Lets see the solution

Q: Write an instruction to swap the high order and low order 4 bits of AL.

A: Below I have provided a  program for the given question.

Q: The content of AC in the basic computer is hexadecimal A937 and the initial value of E is 1.…

A: The content of AC in the basic computer is hexadecimal A937 and the initial value of E is 1.…

Q: CMP INSTRUCTION HAS THE SAME FUNCTION AS Select one: O a. SUB INSTRUCTION WITHOUT SAVING THE RESULT…

A: CMP instruction The value of Operand2 is subtracted from the value in Rn by the CMP instruction.

Q: CMP INSTRUCTION HAS THE SAME FUNCTION AS Select one: a. SUB INSTRUCTION WITH SAVING THE RESULT IN…

A: Let us see the answer below.

Q: Write the instruction format for the jump instruction.

A: Introduction: Instruction format: The instructions that are given to a computer will cause it to…

Q: Which segment will be accessed for the instruction MOV [BX],AH.

A: AX – This is the accumulator. It is of 16 bits and is again divided into two sub-8-bit registers AH…

Q: Data operation stage is happening after the operand address calculation in the instruction cycle.…

A: Instruction Cycle will, fetch stage, decode stage, execute stage.

Q: construct the program for our imaginary computer!   There must be made of at least 5 instructions…

A: Assembly language which refers to the  a low-level programming language that are used for a computer…

Q: The interrupt vector table consists of a number of entries, each of which is a separate data…

A: Dear learner, hope you are doing well, I will try my best to answer this question. Thank You!!

Q: Each item in the interrupt vector table stands for a unique set of information.

A: The answer is given below step.

Q: The CMP instruction is used to compare 2 operands. You can use a jump instruction afterwards. True…

A: CMP instruction is used to compare 2 operands. we can use jump instruction afterwards. Syntax :- CMP…

Q: In the von Neumman model, the PC is used to store: A. The data to use in executing the instruction O…

A: Von Neumann An arithmetic unit, a programme control unit, a single bus enabling memory access, and a…

Q: Question 6 For the MIPS assembly instruction below, what is the corresponding C statement? Assume…

A: The MIPS assembly instructions perform the following operations: Multiply the value of register $s0…

Q: Assume AL=35h; CL=05. Write the content of AL after RCR AL, CL - showing the calculation steps.…

A: Dear Student, RCR instruction in 8086 assembly language is used to perform rotations of all the bits…