B- A Blood warming device contains a 20 mm diameter copper pipe is used to carry warm water, the external surface of the pipe is subjected to convective heated transfer coefficient of h 6 W/m² K, find the heat loss by convection per meter length of the pipe when the external surface temperature is 40 °C and the surrounding are at 20 °C.?

B- A Blood warming device contains a 20 mm diameter copper pipe is used to carry warm water, the external surface of the pipe is subjected to convective heated transfer coefficient of h 6 W/m² K, find the heat loss by convection per meter length of the pipe when the external surface temperature is 40 °C and the surrounding are at 20 °C.?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 4. A car engine with the dimensions 0.6 m high, 0.50 m-wide, and 0.8-m- long. The bottom surface of…

A: Data given-

Q: A. Negligible flow of heat B. No difference of temperature between the bodies ©Heat flow independent…

A: Different conditions of heat transfer are: Steady-state heat transfer Unsteady state heat transfer…

Q: A highly corrosive liquid is cooled by passing it through a circular channel with a diameter of 5 cm…

A: To Find : The rate of heat loss from the liquid. Given : The diameter of hole is The thermal…

Q: Q3/ A house has a composite wall of wood, fiberglass insulation, and plaster board, as indicated in…

A: Given Dataho = 60 w/m2khi = 30 w/m2kAs = 350 m2To find Q & percentage ince

Q: You are designing a storage container for COVID vaccine. The volume of the storage container will be…

A: Given: Thickness of the container→t=20 Cm=0.20 m And direction of the flow is over the 1m and 5 m…

Q: Node at a plane surface with uniform heat flux m, n+ 1 Ay m - 1. n m.n-1 - Ax

A: Please find the solution below

Q: Indirect Cooling With Liquid Nitrogen. You are designing a system to cool an insulated silver plate…

Q: A heater coil is completely immersed in an oil bath that is insulated on all sides except for the…

A: a) Here's a schematic of the system: Heat transfer rates: Heat transfer from the coil to the…

Q: Cold air at 10 deg F is forced to flow over a flat plate maintained at 40 deg C, the mean heat…

A: GivenTa=10oF=(10°F − 32) × 5/9 + 273.15 = 260.928KTp=40oF=(40°F − 32) × 5/9 + 273.15 =…

Q: A very thin silicon chip is bonded to a 6-mm thick aluminum substrate by a 0.02-mm thick epoxy glue.…

Q: A-For a general office room, the exposed wall (with a window, outside winter type) construction is…

Q: A small radiant heater has metal strips 6mm wide with a total length of 3m. The surface emissivity…

A: Area, A = 0.006 X 3 m2 Heat transfer rate, Q = 1600W T1 = 25°C Find…

Q: B. Consider a medium in which the heat conduction equation is given in its simplest form as I OT (-…

Q: The physics of the convection heat transfer of thermosses phenomenon and the mathematical model…

A: Introduction The passage of thermal energy from a body with a higher temperature to one with a lower…

Q: Example 6.21 Water at 50°C enters a 1.5 cm diameter tube with a velocity of 1 m/s. The tube wall is…

Q: Consider a rectangular warehouse with the dimensions of 40m long x 20m widex10m height. The overall…

A: As per BARTLEBY rules i answer only first three sub parts. so i hope you understand.

Q: Q2/ A hot surface at 100 C is to be cooled by attaching 27778 copper fins (k-237 w/m.K), 3 cm long…

Q: An insulated pipe has an inner diameter of 0.05 m and an outer diameter of 0.06 m. If the insulation…

Question

B- A Blood warming device contains a 20 mm diameter copper pipe is used to carry warm
water, the external surface of the pipe is subjected to convective heated transfer coefficient of
h 6 W/m² K, find the heat loss by convection per meter length of the pipe when the external
°C and
surface temperature is 40
the surrounding are at 20 °C.?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve for the cylinder
Citrus fruits are very susceptible to cold weather as extended exposure to subfreezingtemperatures can destroy them. Consider an 8-cm-diameter orange, that is initially at 10°C. A cold front moves inand the temperature drops to -2°C, with a heat transfer coefficient of 25 W/m2K. Using the properties of water for theorange, and given the ambient conditions remain constant for 7 hours, to what depth r will the orange freeze, if itdoes at all. Ignore any latent heat of solidification effects as the orange freezes.
Example 3.3: The temperature at the center of a tender-boiled potato needs to be 98.9°C. Let's take a potato with 4 cm diameter at 5°C and and put it in vigorously boiling water at 100 °C, where convection coefficient is 1200 W/m². c. How much time will it take to cook the potato? Potato properties: density p=1070 kg/m³, conductivity k=0.8 W/m.°c, specific heat c = 3400 J/kg-°C.
You are asked to design a metal hot dog holder for roasting hot dogs over an opencampfire. The holder is to be designed such that while the end holding the hot dogbecomes cherry red (1400oF), the other end can still be held without using aninsulated handle or glove (~95oF). Design it such that it can be used even on awarm, still day, Tf = 90oF (Assume the convective heat transfer coefficient, h, fora horizontal cylinder is uniform over the whole cylinder and equal to 4.0Btu/hrft2oF)
The 0.5 m x 1.2 m wall of an industrial furnace is constructed from L = 0.15-m-thick fireclay brick having a thermal conductivity of 1.7 W/m-K. The temperature distribution, at an instant in time, is T(x) = a + bxwhere a = 1400 K and b = -1050 K/m. Determine the heat fluxes, q, and heat rates, q,, at x = 0 and x = L, in W/m2 and W respectively. Do steady-state conditions exist? W/m2 1x=0 i W/m? i W Ix=0 = Ir=L = i W Steady-state conditions exist.
A spherical tank,the inner diameter 50 cm and is maintained at temperature of 50c,the outer diameter=1m,and the outer temperature With k=204. 23c 1)Calculate therate of heat transfer. 2)if the tank covered by a 120 mm layer of an insulation with k=0.16, calculate the rate of heat transfer. 49 à 10:04
A spherical tank made up of stainless steel is to be used for storage of oil at 150°Cthat is needed for heating purposes in a plant. It is decided to insulate the tank in order todecrease the heat loss to the surroundings, which is at 20°C having heat transfer coefficient of 25W/m2.K. The heat loss is compensated by the heating resistance inside of the tank. There are twotypes of insulating material present at this plant each is enough for covering the tank with onlyone layer. These are;Type 1: k=0.1 W/m.K thickness=5cmType 2: k=0.25 W/m.K thickness=5cmAn engineer is thinking about the most efficient way of covering the tank in order to minimize theheat loss. Please help him for this purpose. Is it more efficient to cover type 2 over type 1 or type1 over type 2? Explain why?
a) A turbine blade 6 cm long and having a cross sectional area 4.65 cm and perimeter 12 cm is made of stainless steel (k=23.3 Wim K). The temperature at the root is 500 C. The blade is exposed to a hot gas at 870 °C. The heat transfer coefficient between the blade surface and gas is 442 W/im K. Determine the temperature distribution and rate of beat flow at the root of the blade, Assume the tip of the blade to be insulated. b) The hot combustion gases of a fumace are separated from the ambient air and its surounding, which are at 20°C, by a brick wall 0.5 m thick. The brick has a themal conductivity of 5 W/mk and a surface emissivity of 0.6. Under steady-state conditions an Page no.1 of 1 outer surface temperature of 120°C is measured Free convection heat transter to the air adjoining the surface is characterized by a convection coefficient of 15 Wim K What is the brick inner surface temperature
no previous attempt pls. ssume adibatic tip
Answers given are correct
In 1 paragraph, make a narrative of what you have learned in Heat Transfer
Need correctly..