The 0.5 m x 1.2 m wall of an industrial furnace is constructed from L = 0.15-m-thick fireclay brick having a thermal conductivity of 1.7 W/m-K. The temperature distribution, at an instant in time, is T(x) = a + bxwhere a = 1400 K and b = -1050 K/m. Determine the heat fluxes, q, and heat rates, q,, at x = 0 and x = L, in W/m2 and W respectively. Do steady-state conditions exist? W/m2 1x=0 i W/m? i W Ix=0 = Ir=L = i W Steady-state conditions exist.

The 0.5 m x 1.2 m wall of an industrial furnace is constructed from L = 0.15-m-thick fireclay brick having a thermal conductivity of 1.7 W/m-K. The temperature distribution, at an instant in time, is T(x) = a + bxwhere a = 1400 K and b = -1050 K/m. Determine the heat fluxes, q, and heat rates, q,, at x = 0 and x = L, in W/m2 and W respectively. Do steady-state conditions exist? W/m2 1x=0 i W/m? i W Ix=0 = Ir=L = i W Steady-state conditions exist.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q: Consider the section of wall as shown in the figure, assuming one dimensional heat flow,…

Q: A composite plane wall consisting of materials, 1.5-in steel (k = 312 BTU-in/HR.ft2.0F) and 2-in…

Q: Q1-A block as sphere made of Teflon initially at a temperature of 90 C is suddenly immersed in a…

A: Criteria for lumped heat capacity analysis: Biot No.<0.1 Low Biot No. value signifies that the…

Q: A highly corrosive liquid is cooled by passing it through a circular channel with a diameter of 5 cm…

A: To Find : The rate of heat loss from the liquid. Given : The diameter of hole is The thermal…

Q: Two heat reservoirs with respective temperatures of 325 and 275 K are brought into contact by an…

A: Given data: T1=325 KT2=275 KL=200 cmA=24 cm2k=79.5 W/m.K Need to determine the heat flux between the…

Q: A copper rod has an initial length 5.0 cm and a thermal expansion coefficient of 16 x 10-6 /K. It is…

Q: Problems within the wall is T(x) = a(L- ) +b where a = 10°C/m2 and b 30°C, what is the thermal con-…

A: Given data as per questionAssumptionsSteady state condition.One dimensional conductionNo internal…

Q: Heat is conducted through a slab composed of parallel layers of different conductivities, 0.0050 and…

Q: Determine the heat-transfer rate from an electronic chip whose surface temperature is 31ºC and has…

Q: Heat is generated in a sphere of radius 1 m at a rate of 1000 W/m3. The sphere is surrounded by air…

A: The radius of sphere is The heat generation rate is The temperature of air is The thermal…

Q: The time evolution of the temperature of an object follows the Newton's cooling laws dT dx where the…

A: Newtons Cooling Law is given as, dTdX=-k (T-Ts) K= 2.2 1/s Ts =25.6 °C t=0 T(t=0) = 200 °C h=…

Q: (5) Consider a wall (as shown above) of thickness L=1 m and thermal conductivity k-1 W/m-K. The left…

A: Given data: Thickness of the wall, L = 1 m Thermal conductivity, k = 1 W/mK Heat transfer…

Q: Explain the term Strain Hardening?

A: The working of the metals below their recrystallisation temperature is known as cold working…

Q: A large 100-mm thick steel plate is initially at uniform temperature T = 180°C at time t = 0. Both…

Q: Using a finite element method, solve the equation d^2T/dx^2 = -f(x) For a 10 cm rod with boundary…

A: Given that, d2Tdx2=-fx ............... 1Where fx=25, T10=160 °C,T10=160 °C, T0=30 °C, Equation…

Q: wo heat reservoirs with respective temperatures of 325 and 275 K are brought into contact by an iron…

A: Given Thermal conductivity, k = 79.5 W/m K Temperature, T1 = 325 K…

Q: Write clearly and explain.

A: Understand that the uniform heat generated is one-dimensional, steady-state conduction. Write the…

Q: (5) Consider a wall (as shown above) of thickness L=1 m and thermal conductivity k-1 W/m-K. The left…

A: Givenq˙=1W/m3k=1W/mKL=1mon both side of wallT∞=1K h1=1W/m2KA=1m2Assumption made-1D heat…

Q: Consider steady-state, one-dimensional heat conduction through the shape shown in the figure.…

Q: Write the heat rate equation only, don’t evaluate. Using table 4.1 in “Introduction to Heat…

A: To determine the heat rate equation for the given system of horizontal circular cylinders using…

Q: Q1: Consider a large plane wall of thickness L= 0.4 m, thermal conductivity k=2.3 W/m °C, and…

A: Given data: Plane wall thickness, L=0.4 m Thermal conductivity of wall, k=2.3 W/m.°C and it's…

Q: A chip that is of length L = 5.5 mm on a side and thickness t = 2.0 mm is encased in a ceramic…

A: Given-Information:- L = 5.5 mmt = 2 mmh = 150 W/m2T∞ = 20°Cq˙ =9×106 W/m3ρ = 2000 kg/m3c = 700…

Question

The 0.5 m x 1.2 m wall of an industrial furnace is constructed from L = 0.15-m-thick fireclay brick having a thermal conductivity of 1.7
W/m-K. The temperature distribution, at an instant in time, is T(x) = a + bxwhere a = 1400 K and b = -1050 K/m. Determine the
heat fluxes, q, and heat rates, q,, at x = 0 and x = L, in W/m2 and W respectively. Do steady-state conditions exist?
W/m2
1x=0
i
W/m?
i
W
Ix=0 =
Ir=L =
i
W
Steady-state conditions
exist.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Model the following heat transfer situations. Specify heat flows and storages. Try to write down the mathematical expressions. (i) Solar heating of the road surface (ii) A steam pipe passing through an open space between two buildings (iii) Heat transfer from a person in a warm room in the cold season (iv) Pressure cooker-warming up-cooling down (v) Pressure cooker-steady conditions (vi) A rod with one end in a furnace and the remaining surface in atmosphere (vii) A wire carrying current, exposed to air (viii) A water heater (electrical) with hot water being drawn out with cold water admission. (ix) Cake being baked in an oven or a fruit placed in a refrigeration (x) A frying pan placed on a stove. 1.2 Choose the correct statement in each question. (i) A pipe carrying steam at about 300°C traverses a room, the air being still at 30°C. The major fraction of the heat loss will be by (a) conduction to the still air (b) convection to the air (c) radiation to the surroundings…
Suppose that the 10 cm thick concrete wall of a commercial building measures 30 mby 4 m. The energy impinging on the surface is 700 Wm-2. Under these conditionsthe external air temperature is 25ºC, and the internal and external surfacetemperatures of the concrete wall are 17ºC and 40ºC, respectively.(a) State and briefly describe the three heat transfer mechanisms.[30%](b) Calculate the net amount of thermal energy radiated by the wall.[40%](c) State your assumptions and briefly discuss their effect on the relativesizes of the heat transfer mechanisms.[30%]Data for Question A3.Heat transfer coefficient of air at 25ºC = 5 Wm-2K-1Thermal conductivity of concrete = 1.2 Wm-1K-1Emissivity of concrete = 0.85Stefan’s constant = 5.7 x 10-8 Wm-2K-4
Check Biot number and do the problem in 20 minutes
Q5/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D=3.34 cm steel pipe (k=54.0W/m. C) for i the following conditions: inside and outside heat transfer coefficients are 2 o 2 o 1200W/m."C. and 2000W/m". C respectively. If the temperature of inner fluid and outer fluid are 600 C and 300 C, calculate the heat transfer through one meter length and the temperature of the outer surface.
Problem 4 A cork board (k = 0.039W/m K) 3 cm thick is exposed to air with an average temperature T.. = 30°C with a convection heat transfer coefficient, h = 25 W/m².K. The other surface of the board is held at a constant temperature of 15°C. A volumetric heat generation of 5 W/m³ is occurring inside the wall. Assuming one dimensional conduction, write the governing equation and express the boundary conditions for the wall. (solve the equation is not required) Problom
Q2/ An aluminum sphere weighting 7kg and initially at a temperature of 533K is suddenly immersed in a fluid at 283K. if heat transfer coefficient between the sphere and fluid is 50W/m?.°C. Take density=2707kg/m3, specific heat=0.9KJ/kg.ºC and thermal conductivity= 204W/m°C. Determine th Bi number and And determine the time required to cool sphere to 263k
1. Saturated steam at 500 K flows in a 0.20 m inside diameter, 0.21 m outside diameter pipe. The pipe is covered with 0.08 m of insulation with a thermal conductivity of 0.10 W/m-K. The pipe's conductivity is 52 W/m-K. The ambient temperature is 300 K. The unit convective coefficients are h; = 18,000 W/m²-K and ho = 12 W/m²-K. Determine the heat loss (kJ/min) from 4 m of pipe. • show conversions, units, and box in your final answers
Answer is correct. Please answer all parts.
Q: Consider the section of wall as shown in the figure, assuming one dimensional heat flow, determine the following: I- Rate of heat transfer per unit area (Im²) through the composite wall. II- Determine also the temperature (Tp) as shown in the figure. To1 30 °C Too2 = 2 °C hi = 20 W/m?.C 8 cm h2 = 12 w/m?.C 20 cm A %3D kA = 0.6 W/m.°C D TD %3D 30 cm kB = 0.8 W/m .°C T01 To2 kC = 0.9 W/m.°C hi B E 10 cm h2 kD = 0.7 W/m .°C kE = 0.5 W/m.°C %3D kF = 0.04 W/m.C 8 cm 6cm. 12cm
Write the heat rate equation only, don’t evaluate. Using table 4.1 in “Introduction to Heat transfer, 6th ed., Wiley”
can you please please work it all out
I need the answer as soon as possible