Arectangular concrete hollow section simply supported beam shown belowhave the following dimensions: b= 10-inch, w = 2 inches and h = 18 inchesand spans 14 ft. The section should carry its own weight and imposed adead load of 150 Ib/ft and a live load of 50 lb/ft. If the young's modulus is10.2 x 10° psi and the density of concrete is 150 Ib/ft³, calculate the:1. Permissible bending stress if the concrete strain is 0.0032. The moment resistance of the beam3. The maximum bending momentbw

Maximum Bending moment of a simply supported beam with Udl at full span =wl28 StressStrain=Young's…

Arectangular concrete hollow section simply supported beam shown below have the following dimensions: b = 10-inch, w = 2 inches and h = 18 inches and spans 14 ft. The section should carry its own weight and imposed a dead load of 150 lb/ft and a live load of 50 lb/ft. If the young's modulus is 10.2 x 10° psi and the density of concrete is 150 lb/ft³, calculate the: 1. Permissible bending stress if the concrete strain is 0.003 2. The moment resistance of the beam 3. The maximum bending moment b w

Arectangular concrete hollow section simply supported beam shown below have the following dimensions: b = 10-inch, w = 2 inches and h = 18 inches and spans 14 ft. The section should carry its own weight and imposed a dead load of 150 lb/ft and a live load of 50 lb/ft. If the young's modulus is 10.2 x 10° psi and the density of concrete is 150 lb/ft³, calculate the: 1. Permissible bending stress if the concrete strain is 0.003 2. The moment resistance of the beam 3. The maximum bending moment b w

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. Minimum as required by NSCP 2015. = [rmin] (5 decimal places)
Q- The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm tested as per the split tensile strength test guidelines of IS 5816:1999 is 157 kN. The split tensile strength (in MPa, round off to one decimal place) of the specimen is?
Use Code for Structural Concrete (ACI 318-19): i need the answer quickly i need the answer in Handwritten.
Design strength for M25 concrete in direct compression, bending compression and flexural tension are, respectively A 10 MPa, 11.15 MPa and 3.5 MPa B 25 MPa, 11.15 MPa and 3 MPa с 10 MPa, 12.5 MPa and 3.5 MPa D 25 MPa, 11.15 MPa and 2.57 MPa
Fill the table.
1 - please show complete solution, thanks!
The flexural tensile strength of M25 grade of concrete, in N/mm², as per IS:456-2000 is A 0.5 B 5 C 2.25 D 3.5
What would be the average compressive strength of concrete if the load at failure of the 3 trials are 55, 100 kg, 54, 800 kg, and 55, 200 kg. Diameter of the sample is 6”. a 31.1 MPa b 30.1 MPa c 30.6 MPa d 30.6 MPa
Using a simply supported pre-stressed concrete beam, explain the following status using stress diagrams: Stress condition due to pre-stress alone. Change of stress conditions due to the increment of external load: Decompression moment (bottom fibre compression = 0); Cracking moment (tensile strength develops at the bottom and starts cracking at the bottom); and Balance state (whole section is at an equal amount of compression).
A flexure strength tests were performed on a concrete beam having a cross section of 0.15x0.15m and a span of 0.45m. If the total load at failure was 37.5kN, calculate the ff:a. The flexure strength of the concrete if center-point was applied.b. The flexure strength of the concrete if third-point was applied.c. Which of the two flexural tests is recommended in determining the flexure strength of the concrete and why?
Referenced concrete Using inner, not outer, triangles On the below
Three concrete cubes of 150 mm side length have been tested in compression at the age of 28 days. The loads recorded were 500, 550, and 520 KN respectively. Using this data: Required Magnitude of strength(MPa) 1)Calculate the average of strength of the tested cubes 2)Give an estimate of the 7 days strength of the concrete tested 3) Give an estimate of the 28 days strength of cylinder made of same concrete 4)Give an estimate of the 28 days splitting tensile strength of the same concrete 5yGive an estimate of the 28 days flexural strength of the same concrete