Answered: eter of the sample is 6”. a 31.1 MPa b…

Engineering

Civil Engineering

eter of the sample is 6”. a 31.1 MPa b 30.1 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Comparing PCC with mild steel, answer the following questions:a. Which one is stronger?b. Which one has a higher modulus or stiffness?c. Which one is more brittle?d. What is the range of compressive strength for a typical PCC?e. What is the compressive strength for a high-strength concrete?f. What would be a reasonable range for PCC modulus?
A 150mm diameter cylindrical concrete specimen was tested for compressive strength. Thestress at failure is 27.6 MPa, what is the maximum applied force in kN?
Three 150 mm * 300 mm concrete cylinders with water to cement ratios of0.4, 0.6, and 0.8, respectively. After curing for 28 days, the specimens weresubjected to increments of compressive loads until failure. The load versusdeformation results were as shown in Table P7.26. Assuming that the gauge length is the whole specimen height, it is required todo the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for all specimens on one graph.c. The ultimate strength for each specimen.d. The modulus of elasticity as the secant modulus at 40% of the ultimatestress for each specimen.e. The strain at failure for each specimen.f. The toughness for each specimen.g. Comment on the effect of increasing the water–cement ratio on thefollowing:i. Ultimate strengthii. Modulus of elasticityiii. Ductilityiv. Toughness. Curves may be approximated with a series of straight lines.
A center-point loading flexural test was performed on a concrete beam with a cross section of 100 mm * 100 mm and a span of 200 mm. If the failure load was 26.9 kN, find the flexure strength.
A cylindrical concrete specimen was tested for compressive strength. The stress at failure was 22.64 MPa when the applied force was 400,000N. What is the diameter of the specimen in mm? Round off your answer to the nearest whole number.
A concrete test cylinder is tested in compression after 7 days of moist curing. If the strength is 22.5 MPa, what do you predict for the projected 28-day strength knowing that the sample only gain 80% strength at 7 days?
Please give me both a and b answers a. If a concrete with 28 day compressive strength of 4500 psi is being poured, then it how much strength would you expect after 7 days(assuming good curing conditions)? Explain how you obtain the 7 day strength? b. Briefly explain the effect of water to cement ratio on concrete strength?
QUESTION.1: Numerous factors have an influence on the compressive strength of concrete. In each of the questions below, mention the circumstance and give brief explanation which would result in a higher strength. a) Concrete loaded during compression testing at a rate of 12 MPa/min. or 120 MPa/min. b) Cylindrical concrete specimens having dimensions of o15x30 cm or ø10x20 cm c)') Concrete specimens having dimensions of cube 20x20x20 cm and cylinder 15x30 cm d)" Concrete cured in the air, cured in the water
Obtain the following, for all problems below: a) The judgment as regards the extent of produced concrete being in accordance with the requirements of the project. b) The impact of the means of sample preparation and testing on the variation of the obtained results. c) The level of “Quality Control" for the produced concrete. d) Prediction of the extent of compliance of the produced concrete – in future – with the project requirements. In case the requirements are not satisfied, what are the steps that should be followed?
150mm diameter cylindrical concrete specimen was tested for compressive strength. TheSample failed when the applied force was 400 kN. What is the compressive stress at failure in MPa?
Two 150 mm * 300 mm concrete cylinders with randomly oriented steelfiber contents of 0 and 2% by weight, respectively. After curing for 28 days,the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table P7.45. Assuming that the gauge length is the whole specimen height, determine the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for the two specimens on one graph.c. The initial modulus of elasticity for each specimen.d. The ultimate strength for each specimen.e. The strain at failure for each specimen.f. Toughness. Curves may be approximated with a series of straight lines.g. Comment on the effect of adding fiber on the following:i. Modulus of elasticityii. Ultimate strengthiii. Ductilityiv. Toughness
Q3: Discuss importance of sieve analysis test conducted on both fine and coarse aggregateQ4: Concrete cylinder placed in universal testing is subject to axial compressive load. Concretecylinder crushed at a load of 85 kilo pounds, calculate compressive strength of concrete. (Concretecylinder has 6 inches diameter and 12 inches height)