An isolated footing withdimensions of (2m x 2m)was laid on a sand layer, ifthis foundation wassubjected to a column loadof 600 kN and a moment of120 kN.m; for this case, theeffective footing dimensionsare:Oa. 1.4m x 1.8mo b. None of the givenanswers are correctO c. 1.3m x 1.6mo d. 1.8m x 1.8m Two footings related to abuilding, the settlementbelow the first one is 1.2cm,the settlement below thesecond one is 2.7cm; if thedistance centre to centrebetween these footings is4m; the angular distortion forthis system is:Oa. 0.001b. None of the givenanswers are correctOC. 0.005O d. 0.2

As per authoring guidelines, if the question number is not specified, the first question or three…

An isolated footing with dimensions of (2m x 2m) was laid on a sand layer, if this foundation was subjected to a column load of 600 kN and a moment of 120 kN.m; for this case, the effective footing dimensions are: O a. 1.4m x 1.8m o b. None of the given answers are correct Oc. 1.3m x 1.6m Od. 1.8m x 1.8m

An isolated footing with dimensions of (2m x 2m) was laid on a sand layer, if this foundation was subjected to a column load of 600 kN and a moment of 120 kN.m; for this case, the effective footing dimensions are: O a. 1.4m x 1.8m o b. None of the given answers are correct Oc. 1.3m x 1.6m Od. 1.8m x 1.8m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5-A 1.5x1.5 m square footing is constructed in a cohesive soil at depth 1.2 m the ultimate bearing capacity for this footing calculated using Terzaghi's equation was 728 kN/m2. If the load has an eccentricity of 0.18 m from the center line of footing what will be the value of ultimate bearing capacity using Meyerhof's reduction factor? a) 633 kN/m2 b) 673 kN/m2 c) 553 kN/m2 d) 728 kN/m2
Determine the elastic settlement using the Schmertmann method of the 10'x 10' footing as shown below. Estimate the elastic modulus using Es = 10(N + 15), where Es is in ksf and N is the corrected SPT value. Loose sand Medium dense sand Loose sand Dense sand Very loose sand DEPTH 5° 10' 15' 20' 25' SPT 10 21 11 15 41 4 Q=250 kips 10' x 10' 0 0.2 0.4 0.6 STRAIN & Layer 1 Layer 2 Layer 3 Layer 4 Laver 5
A rectangular footing has dimensions shown and is acted upon by a dead load of 382 kN and a live load of 536 kN. The column dimension is 307x560 mm where the shorter dimension is parallel to B. The thickness of the footing is 656mm. fc=28 MPa and fy=420 MPa for diameter 20mm bars. A=2.6m and B=5.2m
Design of Rectangular and Combined Footing Question: (See photo) Note: Avoid rounding off values in the course of solution proper as much as possible. ROUND OFF ONLY AT THE FINAL ANSWER.
Subject:( Geotechnical and foundation engineering )
A 3.4 m square footing is proposed to be used to support a 353 mm x 630 mm RC column loaded with 634 kN dead load and 853 kN live load. The bottom of the footing is 2.3 m below the ground. Assume soil weighs 19 kN/m³ and the allowable soil bearing pressure is 314 kPa. The thickness of the footing is 431 mm. f = 21 MPa and f = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m³ as the unit weight of concrete. Note: For two-way shear, use an effective depth measured from the top of the footing until the top of the bottom-most bar (d;) What is the ratio of the Demand Shear Force and the Capacity in Two Way Shear? (Vu/phiVn) Answer is 1.5881 (Complete Solution)
do not answer unless you are a 1000% sure that you are correct
Two footings one circular and other square are founded on the surface of purely cohesionless soil. The diameter of circular footing is same as that of the side of square footing. The ratio of their ultimate bearing сараcities is 4/3 1.3 3/4 1.0
Design an isolated rectangular footing: P(dead load) = 225 kN P(live load) = 130 kN Qa = 180 kPa Df = 1.5 m Unit wt. of concrete = 23.5 kN/m^3 Unit wt. of soil =17.2 kN/m^3 Bar diameter = 20 mm f`c = 20.7 MPa fy = 248 MPa Width of footing, B is limited to 2m only Column = 40 cm x 40 cm Assume height of footing = 350 mm (check adequacy, if failed - increase the depth) Use min. cover = 75 mm Determine the following: (a) Effective Soil Bearing Pressure, Qe (b) Footing Dimension, L (c) Ultimate Soil Bearing Pressure, Qu (d) Check for Shear Criteria (Beam Shear) (e) Check for Shear Criteria (Punching Shear) (f) Required Steel Area (Long and Short Direction)
Please answer #2 thankyou
A 3.3 m square footing is proposed to be used to support a 435 mm x 435 mm RC column loaded with 585 kN dead load and 643 kN live load. The bottom of the footing is 2 m below the ground. Assume soil weighs 19 kN/m3 and the allowable soil bearing pressure is 290 kPa. The thickness of the footing is 459 mm. f'. = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m3 as the unit weight of concrete. Use an effective depth measured from the top of the footing until the center of the bottom-most bar (d1) Calculate the number of bars required in one direction. Answer in multiples of 1