air|(1)V1↑A1QA₂(2) V2h(3)waterQ Air flows through the device shown in the figure below. If the volumetric flowrate of air (Q)is large enough, the pressure within the constriction will be low enough to draw the water upinto the tube. Determine the volumetric flow rate (Q) in m³/s at section (1) to draw the waterinto section (2). Neglect compressibility and viscous effects.Here the density of air 1 kg/m³ and the density of water is 1000 kg/m³. Also, the gravitationalacceleration (g) is approximated at 10 m/s². The cross-section area at section (1) is A₁ = 0.002m², and the cross-section area (2), A2 is four time smaller than A₁, thus A₁ = 4A,. The heightof water column (h) is 0.3 m.

Answered: air | (1) V1 ↑ A1 Q A₂ (2) V2 h (3)…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What must the gauge pressure p be at A if the volume flow rate out of the pipe at point B is 0.0800 m^3/s?
Water enters a house through a pipe with an inside diameter of 20 mm at an absolute pressure of 4 ATM. A 10 mm diameter pipe leads to a second-floor bathroom 5.0 m above. When the flow speed at the inlet pipe is 4 m/s, (a) Find the speed of the water flow and pressure in the bathroom. (b) Find the volume flow rate in the bathroom. (c) What is the horse power rating of the motor pump at the inlet pipe needed? Assuming 60% Efficiency.
The figure below shows a gasoline storage tank with cross-sectional area Asub1, filled to a depth h. The space above the gasoline contains air at pressure psub0, and the gasoline flows out the bottom of the tank through a short pipe with cross-sectional area Asub2. Derive expressions for the flow speed in the pipe and the volume flow rate. Thank you!
4. Water flows steadily from a reservoir tank through a pipe system having various sizes and elevations. Viscous effects can be ignored, and no external force is applied to the system. It is useful to normalize pressure and velocity in such a way that they have a dimension of length, namely 2 and 22, often called pressure head and velocity head, respectively. At points A-G marked in the figure below, evaluate pressure head and velocity head. Also evaluate elevation head (thus, elevation itself) and total head (sum of all three heads). Are total heads at points A-G remain constant? Why or why not? For pressure head, use gauge pressure. For elevation head, use G as a reference elevation (that is, z = 0). 15 ft 6 ft D Flow 6-in Schedule 40 pipe 21 ft 2-in Schedule 40 pipe 1.25-in diameter G
Write the expanded form of Darcy’s Law. Draw a tube full of sand, with piezometers, and label the components of the system.
Only Handwritten Answer
A water discharge 8 m^3/s is to flow through this horizontal pipe, which is 1 m in diameter. If the head loss is given as 7 V^2/2g (V is velocity in the pipe), how much power will have to be supplied to the flow by the pump to produce this discharge? Plot also the EGL and HGL against the given diagram.
Methane in the gaseous state flows at a rate of 0.072 m^3/s in a pipe at a temperature of 27°C and gauge pressure of 148.675kPa (point 1). The pipe is divided into two branches (point 2 and 3), as seen in the figure. If the exit velocity in pipe 3 is 12 m/s with a density of 1.9 kg/m^3, what is the flow rate and velocity in pipe 2? Consider that in section 2 the fluid is leaving with a temperature of 402°C and an absolute pressure of 175 kPa. We have an atmospheric pressure of 101.325 kPa and R_methane = 0.5182 kJ/kg ⚫K. (1) Inflow D1 D3=50mm D2=100mm (3) (2)
Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.
The reservoir tank shown contains fresh water air pressurized to 200 kPa. There is a loss of 3.3 N*m/N due to friction in the pipes. Point 1 is located at the surface of the water and point 2 is in the free stream of the exit spray. The Distance from the water surface to the free stream is 3 meters. The flowrate for the system is .05 m^3/s (Work on paper required) 1. How much energy is provided to the motor by the flowing water? 2. Assuming the motor has an efficiency rating of 83%, how much power is output? Ar Pressure o water DN 50sch 40 motor r coo ON 80 sch 40
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected between two sections of the pipe (the figure); the cross-sectional area A of the entrance and exit of the meter matches the pipe's cross-sectional area. Between the entrance and exit, the fluid flows from the pipe with speed V and then through a narrow ''throat'' of cross-sectional area a with speed v. A manometer connects the wider portion of the meter to the narrower portion. The change in the fluid's speed is accompanied by a change Δp in the fluid's pressure, which causes a height difference h of the liquid in the two arms of the manometer. (Here Δp means pressure in the throat minus pressure in the pipe.) Let A equal 5·a. Suppose the pressure p1 at A is 2.1 atm. Compute the values of (a) the speed V at A and (b) the speed v at a that make the pressure p2 at a equal to zero. (c) Compute the corresponding volume flow rate if the diameter at A is 4.0 cm.The phenomenon that occurs at a when…
A venturi meter is used to measure the flow speed of a fluid in a pipe. The meter is connected between two sections of the pipe (the figure); the cross-sectional area A of the entrance and exit of the meter matches the pipe's cross-sectional area. Between the entrance and exit, the fluid flows from the pipe with speed Vand then through a narrow "throat" of cross-sectional area a with speed v. A manometer connects the wider portion of the meter to the narrower portion. The change in the fluid's speed is accompanied by a change Ap in the fluid's pressure, which causes a height difference h of the liquid in the two arms of the manometer. (Here Ap means pressure in the throat minus pressure in the pipe.) Suppose that the fluid is fresh water, that the cross- sectional areas are 93 cm2 in the pipe and 31 cm² in the throat, and that the pressure is 53 kPa in the pipe and 44 kPa in the throat. What is the rate of water flow in cubic meters per second? Meter Meter entrance Venturi meter exit A…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS