We have a shaft that is subject to both bending and torque. This 'equivalent bending moment' is 4.6kNm. After considering the fatigue factor, the maximum allowable stress for the material is given as 228 MN/m2 Calculate the shaft diameter necessary to support this 'equivalent bending moment'. Give your answer in mm to 2 d.p. If you think it is 50mm then type 50.00.

We have a shaft that is subject to both bending and torque. This 'equivalent bending moment' is 4.6kNm. After considering the fatigue factor, the maximum allowable stress for the material is given as 228 MN/m2 Calculate the shaft diameter necessary to support this 'equivalent bending moment'. Give your answer in mm to 2 d.p. If you think it is 50mm then type 50.00.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hollow steel shaft transmits 600 kW at 500 rpm. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque The answer is 100mm and 50 mm. can you help me this calculation and i give the answer already. and write with pen. tqvm
Multi part question The rotating shaft shown is subjected to a constant force. Shaft material is AISI 1020 cold drawn steel. The shaft was turned on a lathe using standard carbide tooling. No heat treatment of the shaft was performed. Assume 99% reliability based on material property data. Shaft dimensions are shown in the illustration below. All dimensions in mm. External force is 3.927 kN. Calculate the highest alternating stress in the shaft, in MPa. -20 -35 D. 180- -500 3R. -280- -175- -50 D. 25 D.
We have a shaft that is subject to both bending and torque. The shaft experiences: A bending moment of 2kNm, and a torque of 0.8kNm. Calculate the Equivelent bending load on the shaft. Give your answer in Nm to 1 d.p. If you think it is 50.74Nm, then type 50.7.
Parvinbhai
Write legibly, provide manual step by step solution, and diagram for below given problem. A 50cm diameter solid shaft is desired to replace a hollow shaft havng 75cm outside diamter. Consider the strength to be the same, determine the inside diameter of the hollow shaft. Ans. 68.69cm
What is the minimum diameter of a solid steel shaft that will not twist through more than 3° (degrees) in a 6 m. length when subjected to a torque of 14 kN-m? Use G = 83 kN/ m^2. Convert your answers to mm.
A solid steel bar with a circular cross-section has diameter 50 mm, length 1.5 m and shear modulus of 80 GPa. If the allowable shear stress is 48 MPa and the allowable angle of twist is 2.0 degrees, then what is the maximum permissible torque? State your answer in Nm to 1 decimal place.
A 2-inch line shaft is transmitting 20 hp rotating at 200 rpm, carrying two pulleys spaced 30 inches apart which can cause a torsional deflection on it. If the shear modulus of elasticity is 12,000,000 psi, find the angle of twist in degrees. a. 0.573⁰ C. 1⁰ b. 0.75⁰ D. 0.25⁰
A shaft with diameter of 50 mm is subjected to a torque of 3,000 Nm. Calculate the shear stress (in MPa) considering a section with one keyway (dimension are shown). Use Excel spreadsheet posted on Canvas and give correct answer to one decimal place. 14 mm 9 mm M r = 25 mm
I am struggling with this question
1.A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque. 2. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmitted through a 4 : 1 gearing. 3.A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the material ofthe shaft is 42 MPa. If the shaft carries a central load of 900 N and is simply supported between bearing 3 metre apart, determine the diameter of the shaft. The maximum tensile or compressive stress is not to exceed 56 MPa. 4.A cast gear wheel is driven by a pinion and transmits 100 kW at 375 r.p.m. The gear has 200 machine cut teeth having 20° pressure angle and is mounted at the centre of a 0.4 m…
The internal diameter of a hollow shaft is 2/3 rd of its external diameter. Compare the strength and stiffness of the shaft with that of a solid shaft of the same material.