A 100 mm diameter shaft is subjected to a 10 kN.m bending moment and an axial tension force of 150 kN. The shaft is rotating at speed of 2 rad/speed. The power transmitted by this shaft is 16 kWatt. The yield strength of the shaft is 600 Mpa. Use MSST and DET to determine the safety factor for the various types of loading. (Hint: you should find torque applied to the shaft to consider torsional stress)

Q: i cant read this.. can you write it out??

A:

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: i cant read this, can you rewrite

A:

Q: 6. From among the following, the largest increment of pressure is A. 1 Pa B1 psi C. 1 in H₂O D. 1 in…

A:

Q: Please show detailed solution in a handwritten format. Don't use chatgpt. Torque and Maximum shear…

A: Step 1: Step 2: Step 3: Step 4:

Q: Where can i get the values: x2=0.92 and v2 = 13.5079

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Work done: 3 Check KJ Is the work done to the piston or by the piston? The work is done (No answer…

A: The heat is removed from assembly that is the reason it is negative.

Q: What are the units of F in the equation below: F = mg/gc where m is mass in lbm; g is acceleration…

A: Given;m is the mass in lbm (pounds mass).g is the acceleration due to gravity, which is given as…

Q: I needed it to be solved using differential equation

A:

Q: Ideal and real gases are described below. Select a correct description. O a. For a fixed amount of…

A: Ideal gas  Gasses that elastically collide amongst their molecules and that do not have…

Q: The bore diameter of each cylinder in a six-cylinder four-stroke petrol engine is 25 mm and the…

A:

Q: Question2-1 Thermal hot wire anemometers measure the temperature of the flow, and they are very…

A: answer 2-1 False : Anemometers are used for measuring  speed and direction of wind

Q: 1. A pressure transducer is used multiple times to measure the pressure in a tank. It turns out that…

A: Accuracy is how close the measurement to the true values. While precision is how consistent or how…

Q: TXY is suppose to be -40.5 where did -40.7 come from?

A:

Q: Please correctly answer all parts of the question. Thank you will upvote if correct!

A: (2) The Pirani gauge is a robust thermal conductivity gauge used for the measurement of pressures in…

Q: True Story! The 1998-1999 Mars Climate Orbiter mission was declared a total loss in 1999 as there…

A: The actual distance of orbiter from surface is .The distance taken of orbiter taken for calculation…

Q: 1.5 mm + 2.0 mm 2.0 mm 3.0 mm A shear force, S, is applied. This results in shear flow, shown with…

A: Shear flow at a junction is analogous to current at a junction. That is, the total amount of shear…

Q: ADVANCED CHEMISTRY! RATE WILL BE GIVEN! PLEASE WRITE THE COMPLETE SOLUTIONS A Steam at 400 deg C an…

A: Given:P1=8200 KPaT1=400 deg CP2=10 KPaη=0.76

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.