A hollow steel shaft transmits 600 kW at 500 rpm. The maximum shear stress is 62.4 MPa. Find the outside  and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the  maximum torque is 20% greater than the mean torque The answer is 100mm and 50 mm. can you help me this calculation and i give the answer already. and write with pen. tqvm

Q: A solid shaft 2 inch in diameter is subjected into two torques .If the total angle of twist is eight…

A: Givend=2inT1=200 lb ft=200×12=2400 lb in

Q: Find the maximum shear stress in each shaft for the following arrangement. Assume the diameter value…

A: d = 50 mm G = 85 Gpa T3=500 N.m

Q: diameter solid steel cylinder in which a 7 mm diameter hole has been drilled from end B up to point…

A:

Q: This engine is used in a hoist. Motor 2.5 kW with the help of gears with a power of and n = 500 rpm.…

A:

Q: Find the diameter of the solid shaft. Torque = 190 kNm Maximum shear stress = 210 MN/m2

A: Substitute the given values in the Maximum shear stress equation to get the diameter of the shaft.

Q: The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when…

A:

Q: The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 42 Hz. If…

A:

Q: Circular solid ACB shaft is fixed supported between the wall at A and B. If the allowable shear…

A: Allowable shear stress τallowable=42 MPa=42×106 N/m2Let the maximum torque applied at section C be…

Q: Let's consider a shaft having a diameter of 80 mm, subjected to the shown torques. Calculate the…

A: Givend=80mm

Q: 2. The hollow shaft used in the system has the following conditions: B Outer Ø: 110 mm Ø Allowable…

A: Shear stress-induced in the shaft at any location (r) from the center is given by,= = 11/12Where, r…

Q: What is the minimum diameter in mm of a solid steel shaft that will not twist through more than 3°…

A: Given:-Torque, T=14 kN.m=14×106 N.mmθ=3°Length, L=6 meter=6000 mmG=83 GPaTo find:-Minimum diameter,…

Q: Find the required diameter d0 for a solid circle shaft. b) Find the required outer diameter d2 for a…

A: Given: T =1200 NM G=78 GPa Allowable shear stress =40 MPa Allowable rate of twist 0.78/m TO…

Q: A hollow circular section shaft 2.5 m long is firmly supported at each end and has an inside…

A:

Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of…

A:

Q: Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above…

A: Solution:

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 3°…

A: Given data:- Angle of twist =3° Length of the shaft =6 m Torque applied =14 kN-m. G = 83 kN/m2 To…

Q: Find the max shear stress in given data of two circular shafts (S) AND (H)

A: GIVEN DATA; Two circular shaft made same material one solid and one hollow     both have same length…

Q: A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so…

A:

Q: Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.

A:

Q: A hollow shaft transmits 7 MW at 200 rev/min. It is supposed that the maximum allowable stress is…

A: Given, P=7 MW=7×106 WN=200 RPMτ=70 MN/m2=70×106 N/m2G=80 GN/m2=80×109 N/m2θL=0.40/m=0.4×π180…

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

A: Given,

Q: A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is…

A:

Q: QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is…

A:

Q: A hollow circular shaft has an outer diameter of 100 mm and a wall thickness of 25 mm. The allowable…

A: Introduction The generalized torsional…

Q: A steel shaft 2550 mm long must transmit a torque of 34 KN-m. The total angle of twist and the…

A:

Q: T torque is applied to the part made of Aluminum and Steel fixed at A and B points. The diameter of…

A:

Q: A maximum allowable shear stress of 20 kpsi is given. NOTE: This is a multi-part question. Once an…

A:

Q: Please don't provide handwritten solution...

A: First, we need to calculate the torque TBC. The torque TBC can be calculated by subtracting the…

Q: A non-rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to a…

A: The factor of safety. FBD: The free-body diagram is shown below.

Q: 8. A solid steel shaft 5 m long is stressed to 60 MPa when twisted through 4". Find the shaft…

A:

Q: 5. The shaft of a motor has a length of 15 times its diameter and has a maximum twist of 1.5 degrees…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: connected by using a muff coupling. The shaft rotates at a speed of 620 rpm and transmits a power of…

A:

Q: The shaft, described in the previous question, is considered here again. Consider that the maximum…

A: Maximum stress = 490 MPa  Minimum stress = -95 MPa  Find the mean, stress amplitude and summation of…

Q: A solid 2.0 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

A:

Q: Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.