A non-rotating shaft shown in the figure is machined from AISI 1020 CD steel. It is subjected to a force of F = 5kN. Find the minimum factor of safety using Maximum shear stress theory. All dimensions are in mm. 500 25 D.- 20- 20 -35 D. 180- -3 R. 280- -175- -50 D. -25 D. -20 -20

Q: What are the principal stresses? How can they be determined?

A: Principle stresses can be defined as the maximum or minimum normal stresses on a specific plane. The…

Q: What are the general equations of plane stress transformation?

A:

Q: How are the stress components transformed?

A: Consider a plane truss. Let, σx and σy be the normal stress acting along x and y-axis,…

Q: 2.20. The uniaxial yield strength of annealed AISI 1015 steel is 386 MPa. Estimate the shear stress…

A: Given data: It is required to determine the shear stress according to the Tresca’s theory and…

Q: Explain the difference between normal stress and shear stress?

A:

Q: How can we apply the general equations of plane stress transformation?

A: An object is under a biaxial state of stress when the stress exists only inside the 2-dimensional…

Q: In order to obtain the residual stress, is it necessary to know the strain in each segment due to…

A: Residual Stress: They are the stresses that are present in the specimen, after the removal of loads.…

Q: a) Material A is the strongest material (T) / (F) b) Material B is the most rigid material (T) / (F)…

A: As per the guidelines, we are bound to solve only 3 sub parts questions. Please repost the other…

Q: Explain the principle of stress and

A: Principal stresses are maximum and minimum value of normal stresses on a plane (when rotated through…

Q: what the hookes law about stress and strain , states?

A: It is required to explain what is Hooke's law.

Q: Is internal work also called strain energy?

A: Yes, the internal work is also called strain energy. When an external load is applied to the body,…

Q: The diagram below shows a microscopic metal rod with a single crystal structure whose orientation is…

A:

Q: What would happen to the wire if it were stretched beyond its elastic limit? What would happen to…

A: Consider the diagram of stress vs strain for tension test for a typical tensile metal as shown…

Q: Compare between the theoretical and practical stress strain diagram.

A:

Q: Define the term stress trajectory?

A: Stress Trajectory: It is the line continuously showing the changes in orientation of principal…

Q: You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m).  The…

A: The cross section of the square rod is, A=4 mm×4 mm The length of the rod is, L=2.3 m The Young's…

Q: Can we calculate true strain values at point M and F using ɛT = ln(1+ɛ)

A: Given data: Engineering strain at MεM=35%=0.35Engineering strain at FεF=53%=0.53 Need to determine…

Q: What is Shear Stress and explain with example?

A:

Q: CApans the temperature increase it would that number from the temperature er this contact and…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.