A//A 4-pole d.c generator lap wound having sequence diagram shown below write the>le connection If the total current 200 A and the total EMF induced 150 V determine theltage and current per path.BackFront8 10 12 14 16 1820 22 24 26 2WWWWWWWWW1 3 5 7 9 11 13 15 17 1921 2325I

Solution:a) Connection Diagram:The connection diagram for the lap wound generator is as…

Answered: A//A 4-pole d.c generator lap wound…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30MCQ

See similar textbooks

Similar questions

A generator at no-load operates 61 Hz, slope 1MW/Hz. Load 1= 1.0 MW and load 2=0.8MW are connected. Find the frequency before and after adding the load 2. (Using House Diagram)A. 60 Hz & 59 Hz C. 60 Hz & 59.2 HzB. 60 Hz & 59.1 Hz D. 60 Hz & 59.3 Hz
A d.c. series generator supplies the load of 5 kW at 250 volts. The armature resistance and series field resistances are 1 ohm and 0.5 ohm respectively. Determine the value of the induced emf.
A three phase stator is shown below. The positive polarity of the currents is shown in the image. The windings are fed with the following balanced three phase currents: la-lmcos(wt) Ib-Imcos(wt-90°) Ic=Imcos(wt+90°) a) Where would you label the positive axes of all three phase windings in the image? b) Draw the magnetic field vectors produced by each single phase, and the total rotating magnetic field for wt = 0° and wt = 90° in the following figures. c) Is the rotating magnetic field clockwise or counter-clockwise?
An Armature runs at 250 r.p.m. and generates an e.m.f. at 50 Hz. There are 216 slots each containing 5 conductors. The winding is distributed and full pitch. All the conductors of each phase are in series and flux per pole is 30 mWb which is sinusoidal distributed.Calculate the number of pole.
2A. What is another term for "shunt"? a) in series b) in parallel c) compounded d) none of the above 2B. Which of the following is/are a basic type of DC generator connection? a) series b) shunt c) compound d) all of the above
D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage
Please help i want urjent answer i am waiting
A small single phase transformer has 10.2 watts no-load loss. The core has a volume of 750 cu. cm. The maximum flux density is 10,000 gauss and the hysteresis constant of the core is 5 x IO^-4. Using the Steinmetz law, determine the eddy current loss." A. 4.55Watts B. 3.55 Watts C. 5.55Watts D. 2.55 Watts
A d.c. generator generates an e.m.f. of 520 V. It has 2,000 armature conductors, flux per pole of 0.013 Wb, speed of 1200 r.p.m. and the armature winding has four parallel paths. Find the number of poles. 3. [4] (Elect. Technology, Aligarh Univ. 1978)
The shunt field winding of a shunt generator has a resistance of 80 ohms at 20⁰C. After several hours of continuous operation, the winding temperature rises to 50⁰C. How much is the winding resistance under this condition, Assume the resistance temperature coefficient of copper to be 0.004 ohm per degree at 0⁰C.
The incremental cost of generator 1 is Ic1 = 0.2P₁ + 60 and generator 2 is Ic2 = 0.3P₂ + 40 and the ratings of the generators are 150 MW and 250 MW. a) Find the load sharing of generator 1 for a load of 380 MW. MW (Calculate to 2 decimal places) b) Find the load sharing of generator 2 for a load of 380 MW. MW (Calculate to 2 decimal places)
The DC generator in Figure 1 on Worksheet 4 is a____________a) cumulatively connected short-shunt compound DC generator b) differentially connected long-shunt compound DC generator c) differentially connected short-shunt compound DC generator d) series DC generator

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning