a.) Write out all the force components available for the given system. These should be in terms of the given loads, lengths, and angles. b.) Using Python, find the location of the maximum and minimum internal compressive and tensile forces when P1 = 20lb and P2 = 30lb. Do not Include the pin and roller in your locations for deciding this. c.) Generate a contour graph that represents the internal forces at the maximum compressive beam and the maximum tensile beam. The forces you should be using to represent P1 should be 0 to 100 lb. P2 should be 0 to 100lb. d.) From Part C, which force had a larger effect on the maximum tensile and compressive forces. Explain your reasoning. 4 in P1 1 60° P2 5 |

a.) Write out all the force components available for the given system. These should be in terms of the given loads, lengths, and angles. b.) Using Python, find the location of the maximum and minimum internal compressive and tensile forces when P1 = 20lb and P2 = 30lb. Do not Include the pin and roller in your locations for deciding this. c.) Generate a contour graph that represents the internal forces at the maximum compressive beam and the maximum tensile beam. The forces you should be using to represent P1 should be 0 to 100 lb. P2 should be 0 to 100lb. d.) From Part C, which force had a larger effect on the maximum tensile and compressive forces. Explain your reasoning. 4 in P1 1 60° P2 5 |

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

pls help
Inclined plane diagram: Also String 1 String 2 String 1 B C A The diagram above shows Carts B and C which roll without friction over an inclined plane. The plane is inclined at an angle of theta = 0 away from vertical, as shown in the diagram. Carts B and C are connected by an essentially massless string. Another massless string runs from Cart B over a massless and frictionless pulley to a hanging block, Block A.
Hello, I need your help. Topics: Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation, Moment of a Force-Vector Formulation, and Principle of Moment. Note: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. Thank you so much.
Hello, I need your help. Topics: Force System of a Force, Moment of a Force, Moment of a Force-Scalar Formulation, Moment of a Force-Vector Formulation, and Principle of Moment. Note: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. Thank you so much.
Lessons: Static of Rigid Bodies, Force Vector, Addition of a System of Coplanar Forces, Cartesian Vector, Etc. Kindly answer the following with complete solution. Please also draw the free-body diagram or illustration of your figure. Make sure to write with understandable hand-writing. Please send a clear picture of complete solution. I need the answer within an hour at least. I'll rate you with a like/upvote. Thank you.
4.3 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Problem Set 1- VECTOR RESULTANT BY ANALYTICAL METHOD PROBLEM SOLVING: Solve the following problems. Show pertinent solution and box the final answer. 1. The figure below represents a cart viewed from above being pulled by two children and experiencing a frictional force. Determine the net force on the sled by graphical method using a scale factor 1.0 cm = 4.0 N. F, = 8 N 30 "45 Cart f = 6 N F, = 10 N
TOPIC: STATICS 1. Follow the rule correctly. 2. Solve the asked problem in a step-by-step procedure3. Kindly choose the correct answer on the choices4. Double-check your solutions because we need them for our review. Thank you so much for your kind consideration.
Problem 3: Now we will repeat the previous problem using the Cartesian method. Values: FA = 20 N FB = 30 N a = 25° Use the Cartesian method to determine... a) the magnitude of the resultant force on the bolt. b) the angle made by the resultant, as measured relative to the positive x-axis. Break individual forces into Cartesian components This is the method you are probably more familiar with. We are going to break each force into its respective x and y components, and then add the components together to get the resultant. We can therefore check our answers to the previous problem. Add components along x & y FA This is what we do in the real world by the way. When we don't have answers in the back of the book, we use different methods of achieving the same result, and if we don't get the same result, we know something is wrong. Here's an illustration of what we're doing: FIX X α FRY FB FRX Determine magnitude and direction of resultant
5.2 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
4.2 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.