Motiyo 2. A beam element of length L and constant E and I is shown below. If the linearly dis-tributed load (q) and concentrated force (F) act on the beam, compute the equivalentconsistent nodal force vector.X2L/3LFq(x) = Cx2

Answered: 2. A beam element of length L and…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the vectors that satisfy the stated conditions. NOTE: Enter the exact answers using the provided round brackets.. (a) Oppositely directed to v = (1, –8) and half the length of v. w = 4 (b) Length v17 and same direction as v = (7,0, -6). 6. 0, w = -
2) The cantilevered L-bracket has applied loads of P and Q at point A. Find M, V, and N in each section of the structure (from A to B, then B-C). Choose a coordinate system that follows the right hand rule and write equations as a function of x and y for each section. The thickness of the beam is negligible for this problem. 2 Q P
MpQupq rx F, where r is a position vector from any point on the line through P and Q to R and upo is the unit vector in the direction of line segment PQ. The unit vector upo is then multiplied by this magnitude to find the vector representation of the moment. As shown in the figure, the member is anchored at A and section AB lies in the x-y plane. The dimensions are x₁ = 1.5 m, y₁ = 1.7 m, and zi = 1.6 m. The force applied at point C is F=[-150 i+ 135j + 190 k] N. (Figure 1) Figure Yı B < 1 of 1 ▼ Submi ✓ Correct Part C Calculating the moment about AB using the position vector BC Previous Answers MAB =[ Using the position vector from B to C, calculate the moment about segment AB due to force F. Express the individual components to three significant figures, if necessary, separated by commas. View Available Hint(s) 17| ΑΣΦ ↓1 vec Submit Provide Feedback Previous Answers Request Answer X Incorrect; Try Again PPearson → O с 4 ? Res i, j, k] N m Next
Q5) Determine the moment about the point (A) of the three forces on the beam shown in figure M = ( 554 Nm , 550 Nm , 553 Nm ) * %3D F1 = 37 N Q5 A 0.5 m 8 m 6 m 5 m F2 = 16 N
The beam is subjected to the distributed load and the couple shown. If M is slowly increased starting from zero, at what value Mo will contact at B change from the lower surface to the upper surface?
A flag pole has a staked line to keep it from tipping over. The height of the flagpole is 17 ft. The cable can hold a maximum tension of 1500 lb. Determine the moment created at the support Q by the tension in cable. Enter your answer in Cartesian components with units of kip-ft (1 kip = 1000 lb). Round to 3 significant digits. top T a y Values for dimensions on the figure are given in the table below. R. Variable Value a 13 ft b 18 ft M i + а. A = (| k) kip-ft
Multiple forces distributed loads and concentrated loads are acting on a 10m length simple beam shown on the figure. A moment was also found projected by the location. Find the resultant and location of the reaction of the forces. 100kN/m A 1000mm-500- 150kN/m 2250- 200KN 150KN 250KN 100kN 1000 *500-500- 10m 500- 1000 300kN/m 1000 400kNm 1000 -500 B
The beam shown in the figure is subjected to two forces. What would be the resultant moment about point A measured counterclockwise produced by the two forces. F₁ = 375 N F₂ = 500 N A 8 m Select one: O a. 875 N.m O b. -8600 N.m O c. 2600 N.m O d. 4589 N.m 6 m- 5 4 3 5 m-
5. For the distributed load shown below, calculate the resultant force, find where the resultant force acts and find the resultant moment about the fixed end (on the right). What are the support reactions at the wall? The beam is fixed. Note that x is measured in feet. lb lb w(x) = 20- 1.25. ft 5 ft 3 (x - 4 ft) ² 1 X 8 ft
Given the load the diagram of the overhanging beam 900 lb 400 lb 60 lb/ft A 4 ft RA 8 ft 6 ft Rc Which of the following nearly gives the maximum negative moment in Ib-ft? 5480 lb-ft 2480 lb-ft 4480 lb-ft 3480 lb-ft
The figure below shows a moving vehicle represented by two moving loads. The two loads are x = 2 m apart and they are to pass across a simple beam of length L = 13 m. If P1 = 46 kN and P2 = 93 kN, how far will the car travel when the moment induced is maximum. Initial position: P1 X P2 Position at maximum moment: Simply put, what is the distance D (m) when the moment is maximum? D P1 L P2 +
B7

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

2. A beam element of length L and constant E and I is shown below. If the linearly dis- tributed load (q) and concentrated force (F) act on the beam, compute the equivalent consistent nodal force vector. X 2L/3 L F q(x) = Cx 2