Shown below is a rigid beam ABC attached to the wall with a pin joint (A) andsupported by a 0.5" diameter steel rod through a pin joint (B) that is connected to theceiling with a pin joint (D). The rod and pins are made of steel (E=30x106 psi, v = 0.3) andthe pins are 0.375" diameter. When the load P is applied, point C is displaced .003"downwards. Find the following:a. Deformation of the rod BDb. Normal strain in the rod BDc. Normal stress in the rod BDd. Shear stress in the pin at Be. Magnitude of the load P24"12"12"Side view ofpin joint at BBPinBeam

Answered: Image /qna-images/answer/32cd8093-ec07-4c58-9d7f-508f06048cd2.jpg

Answered: a. Deformation of the rod BD b. Normal…

a. Deformation of the rod BD b. Normal strain in the rod BD c. Normal stress in the rod BD d. Shear stress in the pin at B e. Magnitude of the load P

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Required information The part shown is loaded at point C with 280 N in the positive x direction and…

A: Given:P = 280 N (positive X-axis)Q = 205 N (positive Y-axis)d = 10 mm

Q: 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: The normal stress (either tensile or compressive) developed in a member when it is subjected to an…

Q: - 750 mm G. D 225 mm F 900 mm E 1200 mm-

A: Find the reactions at each joint and force in rope.

Q: Segments AB and CD of the assembly are solid circular rods. A) What is the normal stress in segment…

Q: Please Show work clearly and show free body diagram if possible and be sure with the positive and…

Q: If the principal stresses are of opposite signs, then failure occurs in the plane. True or false?

A: Given: The maximum principal stress is σ1=σ. The minimum principal stress is σ2=- σ.

Q: A force P of magnitude 950 N is applied to the pedal shown. NOTE: This is a multi-part question.…

A: The value of force P is 950 N The thickness of the support is t=5 mm

Q: The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate…

A: DefinitionS-N Diagram:The S-N diagram can be used to design components that are subject to cycle…

Q: The axial load 274 kN applied to the lap joint is distributed equally among the three…

A: Given: P = 274 kN n = 3 d = 26.5 mm w = 135.4 mm t = 29.5 mm

Q: e wrenches to ensure that a bolt has a prescribed on when used for connections. If a nut on the bolt…

Q: Quiz ch-2 Strain rosette readings are made at a critical point on the free surface in a structural…

A: Strain rosette readings are made at a critical point on the free surface in a structural steel…

Q: A link in a mechanism is made from round bar. Due to the loading condition, the link is subject to a…

A: Maximum stress is 68 MPa Minimum stress is -27 MPa Required: Alternating stress

Q: Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across…

A: Given: The dimension, n = 7/4 in The dimension, a = 15/32 in The dimension, e = 27/32 in The…

Q: If load P = 22.9 kips, determine the normal force in bar (1). D P P A 6 ft 51.9 kips 44.8 kips 27.3…

A: Given that, P = 22.9 kips The force in bar (1) is obtained by taking the moment of forces about…

Question

Shown below is a rigid beam ABC attached to the wall with a pin joint (A) and
supported by a 0.5" diameter steel rod through a pin joint (B) that is connected to the
ceiling with a pin joint (D). The rod and pins are made of steel (E=30x106 psi, v = 0.3) and
the pins are 0.375" diameter. When the load P is applied, point C is displaced .003"
downwards. Find the following:
a. Deformation of the rod BD
b. Normal strain in the rod BD
c. Normal stress in the rod BD
d. Shear stress in the pin at B
e. Magnitude of the load P
24"
12"
12"
Side view of
pin joint at B
B
Pin
Beam

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Deformation of the rod BD

VIEW

Normal stress in the rod BD

VIEW

Magnitude of the load P

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. parameter value units L. 450 mm L2 300 mm d₁ 40 mm d2 30 mm P 40 KN L1 d₁ P B CC 030 BY NO SA 2021 Cathy Zupke P L2 D U MPa MPa The stress in AB σAB= The stress in CD and EF: σCD = σEF= E F
The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown. (Figure 1) Figure 1 of 1 > Part A If the wheel is subjected to a normal force of P = 3.3 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel. Express your answer to three significant figures and include the appropriate units. Tavg= Submit Provide Feedback Value A Request Answer C Units ? Next >
1. A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 50 kN. The material is AISI 1060 hot-rolled steel (?? =370 MPa,?? =680 MPa ). Use a design factor of 2 and determine the dimensions of the square cross section for the following cases. Neglect any stress concentration. a. The rod must support this load for 100 cycles. b. The rod must support this load for 104 cycles. c. The rod must have infinite life.
The two angle bars are used to support a tensile load "T". Assume the tensile load to be equally resisted by each angle. 400 mm x 20 mm THK Gusset Plate The steel used is L 6 x 6 x 1. Properties: A = 7096.76 mm? y = 47.244 mm Fy = 248 MPa Fu = 400 MPa b = 152.4 mm b. t = 25.4 mm x = 47.244 mm Effective hole diameter = 25 mm y Use case 2 for shear lag factor. Use NSCP 2015 code. 1. Determine the maximum allowable load that can be carried by the two L6 x 6 x1 based on yielding of the gross section--- 2. Determine the maximum factored load that can be carried by two L6 x 6 x 1, based on the fracture of the effective net area.---- 3. Determine the maximum allowable tensile load that can be carried.------ 4. Determine the maximum factored tensile load that can be carried-- bo
10000 lb is applied at G, pin C can have 5000 max horizontal load and 6000 vertical load, determine max angle of bed
A long, slender structural aluminum [E = 69 GPa] flanged shape is used as a l = 9.2-m-long column. The column is supported in the x direction at base A and pinned at ends A and C against translation in the y and z directions. Lateral support is provided to the column so that deflection in the x-z plane is restrained at mid-height B; however, the column is free to deflect in the x-y plane at B. Assume that b; = 102 mm, d = 122 mm, t; = 8 mm, and tw = 6 mm. Determine the maximum compressive load P the column can support if a factor of safety of 2.9 is required. In your analysis, consider the possibility that buckling could occur about either the strong axis (i.e., the z axis) or the weak axis (i.e., the y axis) of the aluminum column. bf C L Lateral B bracing L 2 A
True or false ? State if it’s true or false