A water tank is 6 m in diameter and 14 m high, if the tank is to be completelyfilled .Determine the minimum thickness of the tank plating, if the stress islimited to 35 MPa ? the density of water is 103 kg/m3.O 0.0550 mmO 0.0117 mm0.03312 mmВackSubmitClear formNever submit passwords through Google Forms.This form was created inside of Almaaqal. Report AbuseGoogle FormsW

Given:d=6 mh=14 mσ=35 MPaρ=103 kg/m3

A water tank is 6 m in diameter and 14 m high, if the tank is to be completely filled .Determine the minimum thickness of the tank plating, if the stress is limited to 35 MPa ? the density of water is 103 kg/m3. 0.0550 mm O 0.0117 mm O 0.03312 mm

A water tank is 6 m in diameter and 14 m high, if the tank is to be completely filled .Determine the minimum thickness of the tank plating, if the stress is limited to 35 MPa ? the density of water is 103 kg/m3. 0.0550 mm O 0.0117 mm O 0.03312 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When filled to capacity, the unpressurized storage tank contains water to a height of h = 39 ft. The outside diameter of the tank is 6.3 ft and the wall thickness is 0.707 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft³.) Answers: Maximum normal stress σ = i Maximum shear stress T = i psi. psi
‏صورة من ابو فيصل
The tank shown is fabricated from steel plate. Determine the required thickness of plate which maybe used if the stress along the transverse direction is to be used which is equal to 40 MPa and the internal pressure is 1.5 MN/m2
Determine the volume and the surface area of the half-torus shown in the figure. A = y T²R₂2 π²Rr -R X
The inner diameter of the AB compressed air tank is 160mm, the wall thickness is 1mm.Since the manometer pressure in the tank is 1,6MPa ,at point a at the top of the tank maximum normal stress and determine the maximum plane shear stress.(c=16mm , d=38mm, e =32mm, g=160mm, h=1mm, k =1.6MPa , F=160N)
Solve for the pressure differential in Pa if the temperature inside a 3.46m vertical wall is 23.52°C, and at the outside is -16.27°C. Assume equal pressures at the top. Express your answer in 3 decimal places.
Learning Goal: The element of material below is subjected to the state of stress shown, where a = 102.0 MPa, b = 52.00 MPa, and c = 22.00 MPa (Figure 1) Figure L. C 1 of 1 Review Determine the orientation of the planes of maximum and minimum normal stress, 01 and 2, respectively. Use the value for 02 that is negative. Then use this value to determine the value of 0p1- Express your answers to four significant figures separated by a comma. View Available Hint(s) Opl, Op2 = Submit VE ΑΣΦ ↓↑ Part B - In-plane principal stresses 01, 02 vec VE ΑΣΦΠ (1 SVAR Determine the in-plane principal stresses for the element (as oriented in Part A), and calculate ₁ and 2 such that they correspond with p1 and 0p2- Express your answers to four significant figures separated by a comma. ►View Available Hint(s) vec ? 6149 0 ? MPa, MPa
A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The cylinder is designed to store fluid at 80 MPa:(a) Determine the external pressure necessary to bring the hoop stress at the outer wall of the cylinder to zero. (b) Draw the variations of the hoop and radial stress across the thickness of the wall. Indicate the stress values at both inner and outer radii.
A rod is made of wrought iron and is secured to the piston by a .apered rod and nut and to the crosshead by a cotter. Determine the diameter of a piston rod for a cylinder of 1.6 m diameter in which the greatest difference of steam pressure on the two sides of the piston is 0.27 N/mm². The length of the rod is 2.9 m. The modulus of elasticity is 212 KN/mm² and the factor of safety is 5.
The spherical gas tank is fabricated by bolting together two hemispherical thin shells. If the 510 cm inner diameter tank is to be designed to withstand a gauge pressure of 2802 kPa, determine the minimum number of 28-mm diameter bolts that must be used to seal it. The tank and the bolts are made from material having an allowable normal stress of 130 GPa and 323 MPa,respectively.
The aluminum cube (600x600x600 mm) is put inside a hole of a rigid boundary as shown below. Initially, there is a gap of 0.2 mm between the cube and the rigid boundary. Determine the new dimensions of the cube if a stress of 100 MPa is applied on the top face of the cube and the temperature of the cube increased by 35°C. For aluminum: Ea=73 GPa, va-0.35, aai = 23*10C y. o=100 MPa Rigid boundary Rigid boundary Aluminum cube 600 mm- 0.2 mm
Determine the height of a tank with 2m dia. And thickness of the wall was 2mm , its used for store oil of specific gravity 0.9. the allowable stress in the plates is 125 mpa.