When filled to capacity, the unpressurized storage tank contains water to a height of h = 39 ft. The outside diameter of the tank is 6.3 ftand the wall thickness is 0.707 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surfaceof the tank at its base. (Weight density of water = 62.4 lb/ft³.)Answers:Maximum normal stress σ = iMaximum shear stress T =ipsi.psi

According to the given dataDensity=We need to find The maximum normal stress and The maximum shear…

Answered: When filled to capacity, the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The gas pipeline is supported every 20 ft by concrete piers and also lays on the ground. If there are rigid retainers at the piers that hold the pipe fixed, determine the longitudinal and hoop stress in the pipe if the temperature rises 60° F from the temperature at which it was installed. The gas within the pipe is at a pressure of 600 lb>in2. The pipe has an inner diameter of 20 in. and thickness of 0.25 in. The material is A-36 steel.
The resulting stress distribution along section AB for the bar is shown. From this distribution, determine the approximate resultant axial force P applied to the bar. Also, what is the stress concentration factor?
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 72 mm and the origin of the coordinate system is at centroid of the cross section. Z A a AY 2a O 4a Figure Q2 J.L B 3a a
A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of p = 420 kPa, determine its minimum required thickness if the maximum normal stress is not to exceed 12 MPa.
Determine maximum principal stress
The ring, having the dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. Determine the change in the internal radius of the ring after this pressure is applied. The modulus of elasticity of the ring is E. What is the change in internal radius if p = 80 kPa, r = 20 mm, r₁ = 19 mm, and E = 200 GPa? ANS. 1.44 μm tri W
The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P = 91 kN. What is the average normal stress in the concrete due to this loading? The pipe has an outer diameter of 80 mm and an inner diameter of 70 mm. The modulus of elasticity is Est = 200 GPa for steel, and E. = 24 GPa for concrete.
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 3 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
At a temperature of 33.01 °C a 0.46-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 138.98°C, determine the magnitude of the normal stress (in MPa) in the steel rod if L = 304.28 mm and M = 209 mm. Round off the final answer to four decimal places.
The spherical pressure hull of the undersea submarine, under a research study shown in the figure below, has a 1 meter radius with a shell thickness of 30mm. The pressure hull is made of steel having a yield point of 700 MPa. Consider sea water to have a constant specific weight of 10kN/m³. Determine the depth pressure of submergence that would setup the yield point stress in the spherical shell. Use:p = yy, where y is the depth r = 1m t = 30mm comex
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 2 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
H w help

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS