At the ambient temperature, the A-36 steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe. As a consequence, if the pipe were unconstrained by the rigid supports at A and B, it would elongate by 8, = 4.6 mm. What is the normal stress developed in the pipe? For A-36 steel, Es = 200 GPa. %3D 150 mm . 10 mm- Section a - a -6 m

At the ambient temperature, the A-36 steel pipe fits snugly between the two fuel tanks. When fuel flows through the pipe, it causes the temperature to vary along the pipe. As a consequence, if the pipe were unconstrained by the rigid supports at A and B, it would elongate by 8, = 4.6 mm. What is the normal stress developed in the pipe? For A-36 steel, Es = 200 GPa. %3D 150 mm . 10 mm- Section a - a -6 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spherical pressure hull of the undersea submarine, under a research study shown in the figure below, has a 1 meter radius with a shell thickness of 30mm. The pressure hull is made of steel having a yield point of 700 MPa. Consider sea water to have a constant specific weight of 10kN/m³. Determine the depth pressure of submergence that would setup the yield point stress in the spherical shell. Use:p = yy, where y is the depth r = 1m t = 30mm comex
igure 200 mm 400 mm 20 mm A Section a-a < F₁ 1 of 1 F₂ Determine the state of stress at point A on the cross section of the pipe assembly at section a -a. Take F₁ = 1540 N, F₂ = 1030 N (Figure 1) Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in the case of tension. 4 σA= Part B μA Value Submit Request Answer (Tay) A = Find (Tzy) A- Express your answer to three significant figures and include the appropriate units. μA Units Value Units ? H ?
The aluminium and Steel pipes are fastened to rigid supports at one of their ends and to a rigid plate C at others end derive expression for axial stress in the two pipes
O d. NA = 0.374 , Ng = 2.611 Clear my choice The pipe assembly shown is subjected to a force F = 12 kN and P = 6 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. 1.2 m 0.65 m d= 176 mnm D- 200 mm Cross section Select one: O a. NH =4.07 360=5355 Od.N-8576 solid rounc bar deep wich a 2 5-mm radiu 1:14 AM fla )) ENG 22/4/2021
The connecting rod of a four stroke cycle Diesel engineis of circular section and of length 550 mm. The diameter and stroke of the cylinder are 150 mm and240 mm respectively. The maximum combustion pressure is 4.7 N/mm2. Determine the diameter ofthe rod to be used, for a factor of safety of 3 with a material having a yield point of 330 MPa.Find also the maximum bending stress in the connecting rod due to whipping action if the engine runsat 1000 r.p.m. The specific weight of the material is 7800 kg/m3. [Ans. 33.2 mm ; 48 MPa]
3) A thin-walled cylindrical pressure vessel of diameter of 1.5 m is subjected to an internal pressure that varies continuously from p_min= 0.8MPa to p_max = 4 MPa. Determine the pressure vessel thickness, t, if the pressure vessel is made from steel with an ultimate strength S_u=400 MPa, a yield strength S_y=300MPa, and an endurance limit S_n-150MPa and a safety factor of two is desired. Use Modified Goodman and the maximum normal stress theory.
Before loading the plate, mark a line with the inclination shown. After the load is applied, the slope of the line decreases by 5x10^-3 rad. Determine the normal stress ?. Consider E = 2.1x106 kgf/cm^2 and v = 0.30. Express your answer in units of kgf/cm^2.
The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 700 mm and a wall thickness of 8.9 mm. For a gage pressure of 1.27 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume = 51. s Answers: (a) Normal stress= (b) Shear stress - MPa MPa
How many 10-mm diameter rivets is needed to fasten member BF to the gusset plate at B if the member BF has thickness of 8 mm and the working stresses are 30 MPa for shear in the rivets and 45 MPa for bearing due to the rivets.
The piston-cylinder assembly above has a wall thickness of 0.125" and an outer radius ro= 2 in. If the internal gauge pressure is 1.2 ksi, determine the maximum normal stress in the piston wall. 18 ksl O9 ksi 36 ksi N/A (this does not meet the criteria of a "thin-walled" pressure vessel)
In the following structure if the temperature increases by 20 °C, determine the normal stress in Links (1) and (2). E (GPa) A (mm2) a (1/°C) 11.9x106 Link 1 200 310 Link 2 70 620 22.5x106 500mm 350mm F 千 100mm 300mm (2) 6kN 400mm
* Your answer is incorrect. The composite shaft consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 8.625 in., a wall thickness of 2.6 in., and a length of L₁ = 17 ft. Steel pipe (2) has an outside diameter of 5.8125 in., a wall thickness of 1.14 in., and a length of L₂ = 24 ft. Both pipes have a shear modulus of 12900 ksi. If a concentrated torque of 30 kip-ft is applied to flange B, determine: (a) the maximum shear stress magnitudes T₁, T2 in pipes (1) and (2). (b) the rotation angle (PB/A of flange B relative to support A. Answers: (a) TI = (b) (PBIA L₁ € i 2.511 = i 0.74 B TB L2 (2) ksi, 12 = i с 1.201 X ksi.