The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P = 91 kN. What is the average normal stress in the concrete due to this loading? The pipe has an outer diameter of 80 mm and an inner diameter of 70 mn The modulus of elasticity is E = 200 GPa for steel, and E, = 24 GPa for concrete.

The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P = 91 kN. What is the average normal stress in the concrete due to this loading? The pipe has an outer diameter of 80 mm and an inner diameter of 70 mn The modulus of elasticity is E = 200 GPa for steel, and E, = 24 GPa for concrete.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

F1, F2 and F3 static forces act on the element shown in the figure. F3 AB (distance b) is in the middle of the cylinder (b/2). It has a distance of a= 50mm, b= 900mm. Considering the most stressed section of the member, this I is the diameter d so that only the AB cylinder can carry it safely. Determine using the Maximum Strain Energy Hypothesis (v. oak-600 MPa and S=1.5 Neglect the shear stress of F1 and F3 forces A b F3:2000 B F2 = 5000 N F1:3000N
RS-10. An acetal polymer block is fixed to the rigid plates at its top and bottom surfaces. If the top plate displaces 2 mm horizontally when it is subjected to a horizontal force P-2 KN, determine the shear modulus of the polymer. The width of the block is 00 mm. Assume that the polymer is lincarly elastic and use small angle analysis - 40 mm- P= 2 KN 200 mm
find the longitudinal strtain experienced by the strut it width is 8mm and height is 20mm
A concentrated load of P = 20 kN is applied to the upper end of a pipe with length L = 5 m. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum tension bending stress in the pipe. B A 105.9 MPa O 120.7 MPa O 113.9 MPa O 94.0 MPa 89.4 MPa L D
A flexible connection consisting of rubber plates (thickness t = 9 mm) attached to the steel plates is shown in the figure. The plates are 160mm long and 80mm wide. (a) Determine the force that can be applied to the arrangement, if it is not to exceed a shear stress of 350kPa
Find the strain Stress=35 MPa E=42 MPa
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
A spherical rubber balloon is blown up until its diameter is three times the initial diameter. If E = 10750 psi and v=0.46, determine the stresses in the balloon. Assume the stress-strain behavior is linear. Answer: 0 = i ksi
A. SOLVE FOR THE STRESS IN THE ROD IF ITS CROSS-SECTIONAL AREA 1S 500mm^2. AVILIV ROD A= 500mm^2 1.5m 3m e=50⁰ P=15KN
A member is made of a material that has a specific weight of g = 6 kN>m3 and modulus of elasticity of 9 GPa. If it is in the form of a cone having the dimensions shown in Fig. a, determine how far its end is displaced due to gravity when it is suspended in the vertical position.
A hemp rope L=12 m long and d=42 mm in diameter is supported from one of the roof beams in a gymnasium. Three gymnasts climb this rope together. The lead gymnast has a mass of m1=50 kg, the next gymnast has mass m2=75 kg, and the trailing gymnast has mass m3=50 kg. Determine the maximum stress in the rope (omax), and the stress in the rope at a location between the intermediate and trailing gymanst (023).
Answer the attached file