A concentrated load of P = 20 kN is applied to the upper end of a pipe with length L = 5 m. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum tension bending stress in the pipe. B O 105.9 MPa O 120.7 MPa O 113.9 MPa O 94.0 MPa 89.4 MPa L

A concentrated load of P = 20 kN is applied to the upper end of a pipe with length L = 5 m. The outside diameter of the pipe is D = 330 mm and the inside diameter is d = 300 mm. Determine the magnitude of the maximum tension bending stress in the pipe. B O 105.9 MPa O 120.7 MPa O 113.9 MPa O 94.0 MPa 89.4 MPa L

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 72 mm and the origin of the coordinate system is at centroid of the cross section. Z A a AY 2a O 4a Figure Q2 J.L B 3a a
Figure Part A Fuc= 0.97 5m HA 2m KN Determine the magnitude of the projected component of the F-5 kN force acting along the axis BC of the pipe. Suppose that a 3.1 m and b=4.4 m (Figure 1) Express your answer to three significant figures and include the appropriate units. Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining B ? a 1m 1 of 1
Determine the absolute maximum shear stress (in unit of MPa) for the point H on the bottom surface of a beam with external loadings shown below. The beam has a uniform square cross-section with lateral size a = 0.2 m. 50 kN 50 kN a В Н a 2 m - 2 m 2 m - 2 m
Q:- A bracket is supported by means of 3 rivets of same size, as shown in Fig. Determine the diameter of the rivet if the maximum shear stress is 85 MPa. +8+4| y 3 1 54-63 2 351 X 51kN All dimensions in mm.
The cross section of a concrete dam is shown in the figure. Take the weight-density (= pg) of water to be 10 kN/m³ and that of concrete to be 25 kN/m³. For the given design of the cross-section, find the ratio h/H that is safe enough for the dam to not tip over (about the downstream edge E). Here you will enter the numerical answer. In the handworked file you must show your worked solution. H E 60° H/10 4H/10 h
Determine maximum principal stress
The bar is subjected to a moment of M = 100 N # m. Determine the maximum bending stress in the bar and sketch, approximately, how the stress varies over the critical section.
The steel pipe of length L = 541 mm is filled with concrete and subjected to a compressive force P = 91 kN. What is the average normal stress in the concrete due to this loading? The pipe has an outer diameter of 80 mm and an inner diameter of 70 mm. The modulus of elasticity is Est = 200 GPa for steel, and E. = 24 GPa for concrete.
For the voltage plane in a point represented in the figure, determine: (A) the main tensions. Specify and represent the orientation of the element (B) the tension of maximum shear. Specify and represent the orientation of the element (C) the average normal tension
Find the value of strain stress 30 MPa Modulus of elasticity=65 MPa
A. SOLVE FOR THE STRESS IN THE ROD IF ITS CROSS-SECTIONAL AREA 1S 500mm^2. AVILIV ROD A= 500mm^2 1.5m 3m e=50⁰ P=15KN
Q2. Show that = Cr2(a - 0 + sin 0 cos 0 – tan a cos? 0) is a permissible Airy function for the tapered cantilever of uniform thickness, shown in Figure 2, and derive expressions for the corresponding stresses or, 0g and tre. Also, find the %3D value of the radial stress at 0-0° when a=30°. w/ unit length Figure 2