Q:- A bracket is supported by means of 3 rivets of same size, as shown in Fig. Determine the diameter of the rivet if the maximum shear stress is 85 MPa. T 57 + 60 y 3 +1 2 54.63|- 351 X 51kN Į All dimensions in mm.

Q:- A bracket is supported by means of 3 rivets of same size, as shown in Fig. Determine the diameter of the rivet if the maximum shear stress is 85 MPa. T 57 + 60 y 3 +1 2 54.63|- 351 X 51kN Į All dimensions in mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The bar has a 60 mm by 15 mm rectangular cross section. If P = 50 kN, determine the normal stress…

Q: Consider the figure shown below: Ay - 300 mm The undeformed length of the bar is 300 mm. It is…

A: Given is Length of the bar = 300 mm

Q: Two loads P act as shown, one parallel to x and another parallel to z axes; each load P equals 1850…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

A: Given that: u = 2.3 mm, v = 3.9 mm c = 685 mm α =310, and β = 590 It is required to determine the…

Q: Finding the cross sectional area Stress 22.66 N/mm2 Force=2 N

A: Given data : Force is denoted by F Stress is denoted by σ Required : Cross sectional area

Q: The lap joint is fastened with four 3/4-inch diameter rivets. ➤a. If the allowable shearing stress…

Q: A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in.…

Q: 10/.. find the shear stress in bolts 4 80 kN 80 kN -O- O--O- 300 mm

A: Write the expression for the load acting on the riveted joint.

Q: Q2\ Determine the torsional stress of the cantilever shafts show in the figures below. 86= b T T 5…

Q: Shear Strain A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q…

Q: 1- Find the shear stresses at A and B points when the force V applied to the beam is 20 kN. 200 mm…

A: Given, The width of the I-section, b=125 mm The height of the I-section, h=250+30+30=310 mm The…

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: Solution - Given data - P= 385 N

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: GivenP=375N

Q: For the structure shown below, the shear stress in the pin at B is determined a MPa if it has a…

Q: Determine the maximum value of Qof the Transverse Shear Stress formula [T = (VQ)/(It)] at point p in…

Q: Two bars are connected by means of a rivet of diameter 5 mm as shown in fig. below. Determine the…

Q: Find the resultant shear stress at point A & C for the weldment shown in the figure. Leg size of the…

Q: A) Determine the elongation of the square hollow bar when it is subjected to the axial force P = 120…

A: To find: A) Elongation of the square hollow bar when it is subjected to the axial force P = 120…

Q: 10 cm B 5 cm F

A: Given, d= 5mm F= 15KN RA is the net reaction force at pin A.

Q: Mohr's circle for an element is shown below. If each grid is 15 MPa then the maximum shear stress…

A: Mohr's circle is a two-dimensional graphical depiction of the Cauchy stress tensor transformation…

Q: What is the shear in member BC to the nearest 0.1k? L1 = 9 ft L2 = 8 ft L3 = 12 ft P = 7 k Pc =…

Q: The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the…

Q: The cross section of a beam is shown in Figure 2. The vertical shear force in the beam is 300 KN.…

Q: A and B points are flush mounted. Since the maximum shear stress is = 10N / mm ^2 in the section…

Q: Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the…

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: A bracket is supported by means of 4 rivets of same size, as shown in Fig. 9.37. Determine the…

A: Shear Stress, τ (Rivets)τ=AV where: V= Total shear force A = Area of rivetTotal Shear load, V…

Q: three rivets of 25 mm diameter joins the plates that are each 130 mm wide The shearsress in the…

A: The given data are: d=25 mm=0.025 mb=130 mm=0.13 mτr=80 MPa=80×106 Paτb=120 MPa=120×106 Pa Here, d,…

Q: Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they are…

A: Given: Total force transmit; FT =50*103 KN Force in one fork; F =25*103 KN diameter of pin; d =…

Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…

Q: Determine-- 1)maximum in-plane shear stress in Mpa. 2)direction of maximum shear stress in degree.

A: Given:σx=-300 MPaσy=450 MPaτxy=200 MPa

Q: A bolt passing through a piece of wood is shown below. Determine the average shear stress in the…

Q: Q1: determine the increase in vertical stresses at depth of Z=3.5 m under points A, B and C due to…

Q: onstruct the shear-force diagram and identify the magnitude of the largest shear force (conside ound…

Q: Determine the sheer stress in the rivet in MPa( 3 decimals)

A: Given data: P=14.072 Nd=27 mmt=25 mmNumber of rivets (n)=7 Need to determine the shear stress in the…

Q: The solid rod with radius r=37 mm is subjected to the loading F;=120 kN, F2=38 kN, F3=29 kN. With…

A: Fifth option is correct combined shear stress=4.805Mpa

Q: 1.5 kN 120 mm Outer diameter: 72 mm Inner diameter: 62 mm 150 mm 120 mm 4.5 kN A For element A find:…

A: Evaluate the equivalent couple about longitudinal axis of hollow circular shaft (that is axis…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Q:- A bracket is supported by means of 3 rivets of same size, as shown in Fig.
Determine the diameter of the rivet if the maximum shear stress is 85 MPa.
+8+4|
y
3
1
54-63
2
351
X
51kN
All dimensions in mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The beam is supported by a pin at B and a short link AC. All pins are in double shear as shown in and each has a diameter of 40 mm assume P1=98 kN and P2= 49 kN. A) Determine the average shear stress developed in the pin at A B) Determine the average shear stress developed in the pin at B C) Determine the average shear stress developed in the pin at C
Mohr's circle for an element is shown, each grid is 5 MPa square. A rotated plane through the element is also shown as the line nt. The normal stress on the plane that is rotated from the x face is: I grid square = 5 MPa
A shear force of V = 240 kN is applied to the box girder. (Figure 1) Figure Part A 9A= 28.82 Part B 200 mm B 90 mm μÅ LO 9B = 16.42 200 mm 10 mm. A μÅ C D 180 mm Determine the shear flow at point A. Express your answer to three significant figures and include the appropriate units. MPa 90 mm Submit Previous Answers Request Answer 100 mm 190 mm -10 mm X Incorrect; Try Again; 5 attempts remaining Enter your answer with a different unit type. Review a list of acceptable units. MPa Determine the shear flow at point B. Express your answer to three significant figures and include the appropriate units. ? Pocke Submit Previous Answers Request Answer 1 of 1 ? > Incorrect; Try Again; 5 attempts remaining Enter your answer with a different unit type. Review a list of acceptable units.
Q1/ Find the value of P for the joint shown in the figure if the allowable shear stress is 100 MPa for the rivets. The four rivets are equal, each of 20 mm diameter. | 100 100 200 600 All dimensions in mm.
Question 1 double-shear pin connections at Band D. All pins are 7 mm in diameter. a = 750 mm, b = 350 mm, h= 550 mm, P= 725 N, and 8 = 55° Determine the shear stress in pin B. Answer in MPa rounded-off to 2 decimal places. (1) a b P
The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by the 0.6-in .-diameter pin at A, and the 0.26-in .-diameter cable BC. Neglecting the weight of the boom, determine the shear stress in the pin (in psi) if P = 5205 lb. Round off the final answer to two decimal places.
Determine if the stress in the steel section, aluminum section, and bronze section are compression or tension
millimeter. What are two plates joined by three nails with a diameter of 15 T N the shear stress in the material if the shear forces are 1200 7.1 N/mm 20 20 N/mm 20 12 N/mm 20
The T-section in the figure was created by gluing two rectangular wooden planks of 18 cm in size with glue. Since the glue value of the shear force affecting the section is Ty = 10KN, determine what the minimum safety stress of the glue should be in order to ensure joint security. (Ix = 11016 cm ^ 4) Write the result after the comma, rounding it to two decimal places and specifying. 18cm T. бст tutkal 18cm Y1Scm 6cm
A state of stress at a point A is given by σx = 77 MPa, σy = 3.1 MPa, and τxy = 12 MPa. What is the maximum in-plane shear stress for the point A? Lütfen birini seçin: a. 70.7106 MPa b. 38.8497 MPa c. 83.0846 MPa d. 39.4498 MPa e. None