A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.89 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall. O 42.6 ksi O 31.2 ksi O 39.7 ksi O 36.1 ksi O 33.5 ksi

A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.89 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall. O 42.6 ksi O 31.2 ksi O 39.7 ksi O 36.1 ksi O 33.5 ksi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa. 50 O 2.63 MPa О 3.13 МРа О 3.36 МРа O 2.88 MPa O 2.44 MPa
4. Determine the minimum thickness of the tank plating if the internal pressure is ODD: 1.3MPa EVEN: 1.7MPa and the allowable stress is 33MPa. 300mm 800mm
How do I calculate for sigma seam? Thank you
A thick cylinder of 0.5 m external diameter and 0.4 m internal diameter is subjected simultaneously to internal and external pressures. If the internal pressure is 25 MN/m2 and the hoop stress at the inside of the cylinder is 45 MN/m2 (tensile), determine the intensity of the external pressure,
The storage capacity of a thin cylindrical pressure vessel is 0.028 m³. The cylinder is subjected to an internal pressure of 21 MPa. The length of the cylinder is twice its internal diameter. Determine all the dimensions of the cylinder, if (a) the longitudinal stress does not exceed 160 MPa; and (b) the circumferential stress does not exceed 235 Mpa.
The copper pipe [G = 6,000 ksi] has an outside diameter of 3.375 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 85 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 3.5 ft, and c =7.0 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft. b B C Answers: (a) Tmax psi i rad (b) ¤c = i
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld. O 611 ksi O452 ksi O 653 ksi O 3.77 ksi O 495 ksl
A 6 meter cable is attached to two points of the same elevation on the ceiling room. The two points are three meters apart. A 100N is tied to the center of cable. Determine the stresses in Pascals of each cable if their cross sectional area is equal to 5 mm^2
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the diameter (mm) of the A premium?
A smooth-walled 100 mm edge steel bucket is filled with rubber to form a rubber bucket embedded within the steel bucket. If the rubber hub is compressed by a 100 kN force, determine: a) The normal contact stress between the rubber and the inner walls of the steel. b) The change in volume experienced by the rubber bucket. Consider the following: - The steel bucket is rigid. - There is no friction between the smooth walls of the steel bucket and the rubber (shear stress equal to zero between steel and rubber). - Rubber properties: E = 4 MPa and v = 0.45.
please answer asap and show complete solutions
Determine normal stress.