Given the plane element shown which is an element acted upon by combined stresses. a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's Circle determine the maximum normal stress on the element.

Q: The block is subjected to axial loa normal tension developed at poir the distribution of the normal…

A:

Q: Determine the state of stress at point A on the cross section of the member at section a-a.

A:

Q: The state of stress at the point can also be represented in termsof the maximum in-plane shear…

A: False, The state of stress at the point cannot be represented in terms of the maximum in-plane shear…

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

A:

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: 3. The frame supports the distributed load shown. Determine the state of stress acting at point E.…

A:

Q: 1. For the given state of stress, determine (a) the principal planes, (b) the principal stresses.

A:

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

A:

Q: The rectangular bar has a width of w = 3.00 in. and a thickness of t = 2.00 in. The normal stress on…

A: (a) The magnitude of load P is 59.04 kips. (b) The shear stress on plane AB is 4.8 ksi. (c) The…

Q: 4.17. Determine the components of stress from the results obtained in (a) v=rsin 0, ve = 2r cos 0…

A: Sure, based on the image you sent, which is a circuit containing a battery, resistors, and an…

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Determine the…

A: Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Determine the…

Q: The block is subjected to axial loads. Determine the normal tension developed at points A and B.…

A: The problem is based on strength of material and can be solved as:

Q: For the given state of stress, determine the normal and shearing stresses exerted on the oblique…

A:

Q: Determine the state of stress at point A of the rectangular post shown loaded with concentrated…

A: Ffgg

Q: Three forces are applied to the machine component ABD as shown in Figure 2. Knowing that the cross…

A: Stresses due to load at D Transverse shear stress    TD=P1ACwhere P1=2.5 kN=2500 Nand AC=40x20…

Q: QU For the state of plane stress shown below, construct a Mohr's circle and determine (a) the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Solve using Mohr's circle

A: For the given state of stress, To find: The normal and shearing stresses after the element has…

Q: re, determine the state A and at point B. Dra plume elements at A am results.

A:

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Given:- σx=70 MN/m2σy=50 MN/m2τxy=30MN/m2θ=30° To find:- The magnitude of the normal, tangential,…

Q: 2. determine the maximum normal stress and the maximum shear stress at point O in dia 15 in 3 7 in F…

A: load acting P =15 lbfrom the geometry diameter of the shaft d=0.5"to find (a)  maximum normal…

Q: In the figure shown, determine the normal stresses at AD and BC shearing stress at bolt D bearing…

A: Given data, Diameter of the bolt, d = 16 mm Free body diagram of EDC where, RD and RC are the…

Q: The beam supports the loading shown. Determine the state of stress at points E and F at section a-a.

A:

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

A:

Q: Draw Mohr's circle that describes each of the following states of stress.

A: Given data:- σx =-8 ksi σy =12 ksi τxv=-6 ksi To draw:- Mohrs circle

Q: The state of stress at a point in a soil beneath a level ground surface consists of a major…

A:

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Q: Two vertical forces, each of magnitude P = 22 kips, are applied to a beam of the cross section…

A:

Q: 3. For the state of stress at a point shown, draw its Mohr's circle and determine the ff: (a) the…

A:

Q: A vertical force P is applied at a point C located on the axis of sym-metry of the cross section of…

A: The centroid of the column , y=y1A1+y2A2A1+A2 iny=5X6X2+2X4X26X2+4X2 iny=3.8 in

Q: 6 in. ااه 800 lb

A:

Q: B

A: Given DataHorizontal force at end D of the lever, P=150 lbThe diameter of portion AB of the lever,…

Q: Determine the principal stresses in the beam at point A. Specify the orientation of the element…

A: here's how to analyze the stress at point G:Information Needed:Beam geometry (width and…

Q: The solid cylinder having a radius r is placed in a sealed container and subjected to a pressure p.…

A: Explanation: ◆ The solid cylinder is subjected to a pressure p inside the sealed cylinder.  ◆ The…

Q: . Determine the principal stresses at point A on the cross section of the wrench at section a-a.…

A: The value of force is P=70 lb

Q: The state of plane stress at a point is represented by the stress element below. Determine the…

A:

Q: The cross-sectional area of the bar ABCD is 600 mm². Determine the maximum normal stress in the bar?

A: Assume that the bar ABCD is The load acting on the bar is P The maximum normal stress then act on…

Q: The hollow steel shaft has a diameter of 65 mm and thickness of 5mm, is subjected to a torque and…

A:

Q: The state of plane stress at a on the element. Represent th on an element oriented 60°…

A: Given Data : σx=34 MPaσy=30 MPaζxy=20 MPa

Q: s possible

A: given:σ1=-12ksiτ=6ksi

Q: The 3/4-in.-diameter shaft is subjected to the loading shown. Determine the stress components at…

A: Given data as per the question The diameter of shaft =3/4 in   considering the structure and forces…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.