The element in the image has a horizontal force of 20 N and a vertical force of 25 N. The element was made of a 25.4 mm diameter steel bar. Determine: to. The four states of stress from the farthest place of the forces and obtain the critical point. b. For the critical point, construct the Mohr circle. C. Obtain the maximum principal and normal shear stresses for the critical point. d. The angles at which the maximum normal and shear stresses occur. and. Draw the rotated tension state for the angles obtained and with the corresponding tensions.

Q: 3. Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at…

A: Given Data Dimensions of the beam are 4in×3in Area, A=4(3)=12 in2 Moment of inertia, I=3(4)312=16…

Q: The steel pipe AB has a 72mm outer diameter and a 5mm wall thickness. Knowing that the arm CDE is…

A:

Q: Prob. # 5] A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter…

A:

Q: A simplified model of a basketball hoop is shown. During a basket dunk a player hangs from the rim…

A: Given:Force applied by the player (F) = 320 lbsOutside length of the square tube (L) = 5…

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner radiu…

A:

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: Problem 3. For problem 2, determine the absolute maximum shear stress developed in the bolt shank at…

A: Given: F=18 lbD=0.25 in To find: Maximum shear stress

Q: A force Q of magnitude 3 kips is applied to the machine element AB as shown. The uniform thickness…

A: Thickness is given as 0.8 in and on resolution of the force along horizontal and vertical components…

Q: Construct a Mohr's circle for the following point stresses: o = 60MPa, oy = 10MPa and Txy = +20MPa,…

A:

Q: Required information Consider the given state of stress. Given: X= 5 ksi and Y= 25 ks + + 6 ksi The…

A: The value are

Q: 1. For the given state of stress, determine (a) the principal planes, (b) the principal stresses.

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Given: σx=62 MPaσy=-85 MPaτxy=56 MPa Solution: Sign convention: The tensile stress is positive  The…

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question  Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: Q.1:Answer only one from a & b: a: At a certain point in a stressed body, the stresses are ox= 30…

A: Given: The stress on the x phase is σx=30 MPa The stress on the y phase is σy=-25 MPa The shear…

Q: The rod has a diameter of 40 mm (Figure 1) It is subjected to the force system F, = 1300 N, F, = 615…

A:

Q: Solve using Mohr's circle

A: For the given state of stress, To find: The normal and shearing stresses after the element has…

Q: A bar of diameter 25mm has an axial hole 19mm bored out concentric with the oute circumference. The…

A:

Q: Compute the maximum shear stress (r7maz) that this solid can have. Hint: Problem 3 Use the Mohr's…

A: For solution refer below images.

Q: On section a-a, determine the stress state at points A & B. Neglect the weight of the block. If the…

A: Find:stress state at point A and B

Q: The box wrench is subjected to the P = 38 lb force. (Figure 1) Determine the principal stresses at…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Determine the equivalent state of stress on an element if it is oriented 30° clockwise from element…

A:

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

A:

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

A:

Q: A thick cylinder internal diameter 240mm external diameter 240mminternal diameter ‘D’ is subject to…

A: In this problem, we will calculate the internal diameter of the thick cylinder, A thick cylinder is…

Q: How is the state of plane stress at the point uniquely represented?

A: If the stress state at a material particle is such that the only non-zero stress components act in…

Q: s, (c) the orientation of the planes maximur num in-plane shearing stress, (e) the cor

A: Given data sigma x = 18 kpsi sigma y = 12 kpsi shear stress = -8 kpsi  required  Principal stress…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.