Prob. # 5] A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter and 375 mm external diameter. The projecting ends of the steel rod are provided with nuts and washers. The nuts are tightened up so as to produce a pull of 5 kN in the rod. The compound is then placed in a lathe and the brass is turned down to 4 mm thickness. Calculate the stresses in the two materials.

Prob. # 5] A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter and 375 mm external diameter. The projecting ends of the steel rod are provided with nuts and washers. The nuts are tightened up so as to produce a pull of 5 kN in the rod. The compound is then placed in a lathe and the brass is turned down to 4 mm thickness. Calculate the stresses in the two materials.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram
6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 10 mm. A GASKET IS INSERTED BETWEEN THE FLANGE AT ONE END OF THE PIPE AND A FLAT PLATE USED TO CAP THE END. HOW MANY 40 mm- DIAMETER BOLTS MUST BE USED TO HOLD THE CAP ON IF THE ALLOWABLE STRESS IN THE BOLTS IS 105 MPa, OF WHICH 55 MPa IS THE INITIAL STRESS ? WNHAT CIRCUMFERENTIAL IN THE PIPE ? TO TIGHTEN THE BOLT INITIALLY, AND WHAT WILL STRESS IS DEVELOP WHY IS IT NECE SSARY HAPPEN IF THE STEAM PRESSURE SHOULD CAUSE THE STRESS IN THE BOLTS TO BE TWICE THE VALUE OF THE INITIAL STRESS?
attached can solve wrong
The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of 280 MPa.
A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which has an outside diameter of 40mm and an inside diameter of 30mm. The length of the brass tube exceeds that of the round steel bar by 0.12mm. Rigid plates are placed on the ends of the tube through which an axial compressive force is applied to the compound bar. Determine the compressive stresses in the bar and tube due to force of 60 kN. Use 200 GPa for modulus of elasticity of steel and 90 GPa for modulus of elasticity of brass.
Define the main difference between thick and thin cylinders and give an example for each type of cylinder Derive the expression of longitudinal stress, o, for a closed thick cylinder which has inner radius, R₁ and outer radius, R₂ and subjected to internal pressure only. Figure Q3 shows a cross section of composite cylinder that is made by shrinking a tube of 330 mm internal diameter and 50 mm thick over another tube of 330 mm external diameter and 50 mm thick. The radial pressure at the common surface, after shrinking is 180 MPa. Suppose the compound cylinder is subjected to an internal fluid pressure of 1200 MPa, determine; i) the hoop stresses at inner radius and outer radius of inner cylinder, ii) the hoop stresses at inner radius and outer radius of outer cylinder. Ro P Figure Q3 R₁
4. A thin cylinder of inner radius 500 mm and thickness 10 mm is subjected to an internal pressure of 5 MPa. The average circumferential (hoop) stress in MPa is
3. A circular steel cylinder of external diameter 0.2 m and internal diameter 0.1 m is shrunk onto a circular aluminium alloy cylinder of external diameter 0.1 m and internal diameter 0.05 m, where the dimensions are nominal. Determine the radial and hoop stresses at the bores and outside surfaces, such that when there is an internal pressure (retained by end caps) of 300 MPa, the maximum hoop stress in the inner cylinder is 150 MPa.
A cylindrical pressure vessel is designed using steel plating with a thickness equivalent to 15 mm. The inside diameter is 460 mm and its height is 2.5-m. Solve for the maximum internal pressure that can be implied if the longitudinal stress is only up to 120 MPa, while the tangential stress is only up to 50 MPa.
Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: 0,05 and Txs 72.2 144.4 144.4 MPa A,B A,B A,B a. Determine Gmin, Omax, and its direction (in degrees) from x-axis at point A. b. Determine Omin, Omax, and its direction (in degrees) from x-axis at point B. B S A " O X
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.