A steel pipe assembly supports aconcentrated load of (P = 22 kN) as shown in Figure. The outside diameter of the pipe is (142 mm) and the wall thickness is (6.5 mm). Determine the normal stresses produced at points H. Use A= 2767 mm2 ,Iz= * 6364867 mm4 -370 mm- 600 mm H K 7.6 MPa (C) O 82.9 MPa (T) 82.9 MPа (С) 98.8 MPа (С) О

A steel pipe assembly supports aconcentrated load of (P = 22 kN) as shown in Figure. The outside diameter of the pipe is (142 mm) and the wall thickness is (6.5 mm). Determine the normal stresses produced at points H. Use A= 2767 mm2 ,Iz= * 6364867 mm4 -370 mm- 600 mm H K 7.6 MPa (C) O 82.9 MPa (T) 82.9 MPа (С) 98.8 MPа (С) О

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A machine component is fabricated from a bent tube as shown below. One part of the tube lies along the z- axis, and the other part is parallel to the y-axis. The outside diameter of the tube is do 122 mm and its inside diameter is dį = 108 mm. A force F = 8.5 kN acts along a line from point to point D. Determine the principal stresses and the absolute maximum shear stresses at points A and B. Note that point A lies along the y-axis and point Blies along the x-axis. Given: • L₁ 258 mm L₂ = 118 mm • L -281 mm LA-602 mm 4 P (α₂₁)A- (₁2) A (Tmax) A L2 Z ²1 00 B L₁7 number (rtol=0,01, atol=1e-05) number (rtol-0.01, atol-1e-05) number (rtol-0.01 atol-le-057 F 0 MPA LA D L3 y 0 0
-L2 F1 L1 F2 A solid member with a diameter of 35 mm is subjected to loads as shown in figure above. If L1=62 mm, L2=102 mm, L3=49 mm, F1=1467 N, and F2=2420 N; Determine the normal stress (MPa) at point K. Use - sign if it is compressive. Determine the shear stress (MPa) at point K. Use proper sign. Determine the magnitude of the maximum in-plane shear stress (MPa) at point K.
1)In a thin plate, the state of stress prevails according to the figure. Calculate the principal stresses and their directions (using both equations and Mohr's stress circle). Show the result in a figure. σx = 40 MPa; σy = 50MPa and τxy = 30 MPa 2)A cylindrical pin made of carbon steel is loaded with a maximum possible twisting moment Mv. Maximum allowedshear stress is Tmax = 40 MPa. The pin has the diameter measurement d = 50 mm, and the length measurement L = 250 mm.Calculate the free end distortion θ in degrees. G=80 GPa.
Calculate the main stress plane and main stress at the plane stress conditions as shown in the following figure.
A circular bracket with a diameter of 100 mm is fixed to a wall as shown in the figure below. Determine and draw the state of stresses in small infinitesimal cubic elements located at pooints M and N on the cross section A.
Read the question carefully and give me answer according to the question
A torque and two forces seen in the figure are applied. the diameter is 65mm. Determine the principal stresses And the maximum shear stress at K.
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the normal stress at point A.
Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an internal pressure of 60 MN/m2 and an external pressure of 30 MN/m2. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches
The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure. The bar width is w = 2.25 in. and the bar thickness is 0.375 in. For an applied load of P = 4,800 lb, determine the average bearing stress produced in the bar by the 0.775-in.-diameter pin. Express your answer in psi rounded to the nearest hundredths.
pru 7 Oy enüz žvaplanmadı Ot .00 üzerinden aretlenmiş Txy Soruyu aretle Ka Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=61 MPa, oy=32,7 MPa and Txy=-28,1 as shown in figure (a). Determine the maximum principal stress (MPa). Note: If the stress is compressive, use - sign. Yanıt:
When there is a plane stress condition as shown in the figure, display this stress in the form of the maximum in-plane shear stress and the corresponding average vertical stress.