H.W: A steel pipe with an outside diameter of 4.500 in. and an inside diameter of 4.026 in. supports the loadings shown in the figure. Determine: (a) The normal and shear stresses on the top of the pipe at point H. (b) The normal and shear stresses on the side of the pipe at point K. (c) The principal stresses and the magnitude of the maximum in-plane shear stress at point H, and show the orientation of these stresses on an appropriate sketch. (d) The principal stresses and the magnitude of the maximum in-plane shear stress at point K, and show the orientation of these stresses on an appropriate sketch. 3,700 lb-ft 15 in. 2,300 lb 4,200 lb 9 in. FIGURE 1,700 lb

H.W: A steel pipe with an outside diameter of 4.500 in. and an inside diameter of 4.026 in. supports the loadings shown in the figure. Determine: (a) The normal and shear stresses on the top of the pipe at point H. (b) The normal and shear stresses on the side of the pipe at point K. (c) The principal stresses and the magnitude of the maximum in-plane shear stress at point H, and show the orientation of these stresses on an appropriate sketch. (d) The principal stresses and the magnitude of the maximum in-plane shear stress at point K, and show the orientation of these stresses on an appropriate sketch. 3,700 lb-ft 15 in. 2,300 lb 4,200 lb 9 in. FIGURE 1,700 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
800 N D 120 N.m d = 8 cm 600 N Q / If the cross section of the femur can be approximated as a circular tube, determine the state of stresses on the 160 N.m points A and B at section due to the loads as shown in figure. r. = 22 mm n = 18 mm В L = 0.15 m
4. The state of stress at a point, for a body in plane stress, is shown in the figure below. If the minimum principal stress is 10 kPa, then the normal stress oy(in kPa) is Gy 100 P (A) 9.45 (B) 18.88 (C) 37.78 (D) 75.50
In a plane stress condition, the components of stress at point are ox = 20 MPa, ơy = 80 MPa and Txy = 40 MPa. The maximum shear stress (in MPa) at the point is
The bent pipe has a 1.5-in. outer diameter and a 0.2-in. wall thickness. Calculate the largest shear stress that occurs in (a) segment BC; and (b) segment AB. Neglect the stress due to the transverse shear force.
A steel pipe with an outside diameter of 4.67 in. and an inside diameter of 4.25 in. supports the loadings shown. Assume x₁ = 17 in., x2 = 6 in., Px = 3600 lb, Py = 1900 lb, P₂ = 2000 lb, and T = 4500 lb-ft. (a) Determine the normal and shear stresses On, Txy on the side of the pipe at point K. (b) Determine the principal stresses (0,1 > 2) and maximum in-plane shear stress magnitude Tmax at point K, and show the orientation of these stresses in an appropriate sketch. H T Answers: On = i Txy= op1 = Op2 = i Tmax = i M. X1 K Ps ksi. ksi. ksi. ksi. ksi. Px
The thickness of the bracket is 0.75 in. Draw a neat Mohr's circle 3 kips for the state of stress at point K, and use the Mohr's circle to determine 30 K. 2.5 in. (a) the principal stresses at K, (b) the maximum in-plane shear stress and average normal 2 in. 5 in: stress at K. Sketch the answers on correctly rotated elements.
Learning Goal: The state of in-plane stress at a point on an element of material is shown. Let o = 55.0 ksi, oy = 16.0 ksi and Try = 10.0 ksi. Use this information to represent the state of stress of the same point that is rotated through an angle of 0 = 35° b b OT ▼ Part A - Normal and shear stress on element sectioned at plane a a Using the element sectioned at plane a-a and the rotated coordinate system shown, determine the normal and shear stresses, or and Try, respectively, acting on plane a-a ▼ Part B - Normal and shear stress on element sectioned at plane b-b Using the element sectioned at plane b-b and the rotated coordinate system shown, determine the normal Or Try and shear stresses acting on plane b-b. Express your answers in ksi to three significant figures separated by a comma. View Available Hint(s) VE ΟΙ ΑΣΦΑΛΙ b vec 0 ksi
The built-up shaft in figure consists of a pipe AB and a solid rod BC. The pipe has an inner diameter of 20 mm and outer diameter of 28 mm. The rod has a diameter of 12 mm. Determine the average normal stress at points D and E A 4 kN D B 6 kN 6 kN E -8 kN
For the shown element, what are the principal stresses and their orientations (ew, cew), draw the new element 40 MPa + 35 MPa 60 MPa
Need only handwritten solution only (not typed one).
Calculate the principal normal stresses and their directions, the maximum shear stresses and the stresses that will occur on the inclined (C) surface of the stress element whose stress state is given in the figure, by drawing a shape with the MOHR CIRCLE METHOD. Show the stresses you find in the stress element. Show the findings on the Mohr circle and, where necessary, on the element. σx= 500kg/cm^2 ,, σy=750kg/cm^2 ,, τ= τxy= τyx =300kg/cm^2 ,, α=45 degrees