The hollow drill pipe for an oil well (see figure)is 6.2 in. in outer diameter and 0.75 in. in thickness.Just above the bit, the compressive force in thepipe (due to the weight of the pipe) is 62 kips and thetorque (due to drilling) is 185 kip-in.Determine the maximum tensile, compressive,and shear stresses in the drill pipe.

Q: F 30° ød. 2 M. 10

A:

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

A:

Q: Q7-Q8: A 6-in.-long bronze tube, with closed ends, is 3 in. in diameter with a wall thickness of…

A: Longitudinal Stress, σlong = σx = 15 ksi. Tangential Stress, σtang = σy = 45 ksi.

Q: A thin-walled cylinder tank is subjected to a tensile stress of 100 Mpa. What is the longitudinal…

A: The tensile stress on the thin-walled cylinder tank is σt=100 MPa.

Q: For the figure below, Determine the following: 10 MPa 40 MPа 50 МPа The oavg is equal to in MPa: The…

A:

Q: A pressurized pipe with an outside diameter of 14.35 in. and a wall thickness of 0.25 in. is…

A:

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

A:

Q: A point On a free surface of a machine point (E = 214Gpa, G= 83Gpa) the stress state is shown on the…

A: GIVEN :- E = 214Gpa G= 83Gpa σy=15 MPaσx=-30 Mpaζxy=25 MPa

Q: In the given diagram, find the normal and shear stresses at point 'P'? IÊ -500 mm-

A: Given:F=600 Nd=30 mm

Q: 3. Compute the shear stresses. At the top of the side wall the thickness, 1, is 24 in. The torsional…

A:

Q: Z -300, mm 500 mm- $ 30 mm X 600 N The normal and shear stresses in MPa at point P are respectively…

A: To find: The normal shear and shear stress in MPa at point P. Given: The force at point O is F=600…

Q: Estimate the normal stress (on) and shear stress (t) on the inclined plane as shown in the below…

A:

Q: A roadway sign weighs 5 kN and is supported by a structural pipe that has an outside diameter of 295…

A:

Q: Find the value of maximum principal stress Maximum shear stress=80 MPa Minimum principal stress=30…

A:

Q: A steel pipe of length L= 5 ft, outside diameter d₂= 9.3 in., and inside diameter d₁= 4.7 in. is…

A:

Q: Find the maximum shear stress if maximum principal stress is 30 MPa Minimum principal stress 20 Mpa

A:

Q: 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the a

A:

Q: At a party, a parent is blowing up a birthday balloon until its diameter is n = 3.4 times the…

A: Introduction In this problem, we will compute the normal stress in the balloon after inflation, for…

Q: For the pressure vessel in which the loading condition is seen in the figure determine the maximum…

A: Note: the stress values are calculated for the point “a” on the top of the cylindrical pressure…

Q: he stress element shown in the figure below is subjected to the indicated stresses of magnitude || =…

A:

Q: A typical aluminum-allóy scuba diving tank is shown in thế ngure. The outside diameter óf the tank…

A: Solution:

Q: With pressure steel tank axis α = 750 manufactured as degree angle helical welded references Tank…

A:

Q: Consider the stress element below. (a) Determine the three principle stresses and three shear…

A:

Q: Determine Value of x if the Normal stress at rod is equal to the stress at rectangular pipe A =400…

A:

Q: Find the value of maximum principal stress Maximum shear stress=80 MPa Minimum principal stress=30…

A: Given data : Maximum shear stress ζMax=80 MPa Minimum principal stress σ2=30 MPa   Required :…

Q: 80 MPa 60 MPa

A: Consider the given plane figure on x-y plane. From the figure, Stress in x direction = σx = 0 MPa…

Q: A steel pipe with an outside diameter of 4.67 in. and an inside diameter of 4.25 in. supports the…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal vertical planes at…

A:

Q: For the figure shown below. Calculate the increase in vertical stresses (Ac) at point A at depth of…

A:

Q: A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the…

A: given :Thickness of plate, t=0.6 inplate shear stress, τ=31 ksid=0.5 ina=2.75 in

Q: For a min. principle stresses of 30MPA when will the rock fail? Draw the two faults on the resulting…

A: Mohr's circle is a two-layered graphical portrayal of the change regulation for the Cauchy stress…

Q: A torque and two forces seen in the figure are applied. the diameter is 65mm. Determine the…

A:

Q: The normal stresses at a point are o, = 80 MPa and oy = 20 MPa; the shear stress at this point is…

A:

Q: 60 MPa 30 MPa 45 MPa

A: On the given element, Stress in x direction = σx = 45 MPa Stress in y direction = σy =  -60 MPa…

Q: Find the value of maximum principal stress Maximum shear stress=80 MPa Minimum principal stress=30…

A:

Q: For the below stress element, calculate: 1- All the principle stresses 2- Maximum Shear stress and…

A: Given:σx=500 MPaσy=-100 MPaτxy=400 MPaFind:1 All the principal stresses2 Maximum shear stress and…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.