A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate the maximum axial stress of the shaft if the average punching shear stress in the collar and the average bearing stress between the collar and the plate are limited to 100 and 125 MPa, * .respectively F100 mm- 150 mm Collar 25 mm

A vertical shaft is supported by a thrust collar and bearing plate, as shown in Figure. Calculate the maximum axial stress of the shaft if the average punching shear stress in the collar and the average bearing stress between the collar and the plate are limited to 100 and 125 MPa, * .respectively F100 mm- 150 mm Collar 25 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Topic: FUNDAMENTAL CONCEPT OF STRAIN (statically indeterminate) and TORSION (circular shafts and thin-walled tube) Prob. The cross section of the steel tube (G = 11 x 10^6 psi) as shown carries a 50 kip·in torque. Calculate (a) the maximum shear stress and (b) the angle of twist per foot of length.
can sameone solve this thanks .
2- Compare the weight of equal lengths of hollow and solid shafts to transmit a torque T for the same maximum shear stress. For hollow shaft, the inner and outer diameters have relationship D; = 2/3 D, = 2/3 Diollow-
1 of 1 T -1.5m Q: Aluminum shaft of 30mm diameter and 1.5m lenght is subjected to a torque of 500N.m as in figure. Take shear modulus as 80MPA Determine: A- The Max. shearing stress introduced by the shaft. B- The angle of twist in degree. C- The shear strain in the shaft. D- The Min. Shearing stress in the shaft
A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The allowable shear stress in the steel is 40 MPa. G=70 GA (a) What is the required diameter d of the shaft if it is operated at 1500 rpm? (b) What is the required diameter d if it is operated at 3000 rpm? (c) If the length of the shaft from the motor to the gear is 1 m, what are the angles of twist for the two speeds of rotation? Motor Motor
Figure Q5 shows a thick cylinder of 50 mm internal radius and 130 mm outer radius is subjected to an internal pressure of 60 MN/m2 and an external pressure of 30 MN/m2. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches
In the figure, the steel shaft with a diameter of 36 mm is 240 mm diameter pulley. Belts also formed under given angles If the tensile Forces are 2400N and 400N, the shaft at point K on the x-z plane Calculate the normal and shear stresses. Plotting the stress state for this point show me The shaft can carry safely if shear stress em=100 MPa Maximum Shear stress (Tresca)
40 mm Calculate the greatest draft and compression stresses in the a-a section when a force of P = 8000 N is applied to the vice in the figure (dimensions are in mm). 10 mm 50 mm 10 nun section a-a
P
100 kip 10 kip ft The 4-in. diameter shaft shown above is made from a ductile brass alloy. Which of the following are closest to the principal stresses in the shaft? 01 = 31.8 ksi 02 = 76.4 ksi = 94.0 ksi 02 = -62.1 ksi O0g - 14.3 ksi 02 = -6.37 ksi Oo= 7.96 ksi 02 = 9.55 ksi
Please I need help. This problem involves torsional strain. Thank you.
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 10800 psi, and the vertical deflection of joint D is not to exceed 0.425 in. when a load of P = 3100 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 84 in., b = 32 in., and c = 36 in. Part 1 Answer: T = a i D P B Calculate the torque being applied to the shaft at point B. b C lb-in